AMLDW-6070-RZ Datasheet, PDF (1/3 Pages) AIMTEC – LED Driver

FEATURES:
• Step Down DC/DC LED driver
• Constant current output
• Ultra Wide (7:1) input voltage range
• High efficiency up to 97%
• IP67 Case
Click on Series name for product info on aimtec.com
Series AMLDW-RZ
Up to 1000mA | LED Driver
• Operating Temperature range -40ºC to +85ºC
• Open and Short LED Protection
• PWM / Digital Voltage dimming
• Output power up to 56 Watts
Models
Single output
Model
Input Voltage Output Voltage Maximum Rated
(V)
(V)
Current (mA)
Max
Capacitive
Load (uF)
Efficiency
(%)
Ripple &
Noise
(mV p-p)
AMLDW-6030-RZ
9-60
2-56
300
2.2
97
250
AMLDW-6035-RZ
9-60
2-56
350
2.2
97
300
AMLDW-6050-RZ
9-60
2-56
500
2.2
97
350
AMLDW-6060-RZ
9-60
2-56
600
2.2
97
400
AMLDW-6070-RZ
9-60
2-56
700
2.2
97
400
AMLDW-60100-RZ
9-60
2-56
1000
2.2
97
450
NOTE: All specifications in this datasheet are measured at an ambient temperature of 25°C, humidity<75%, nominal input voltage and at
rated output load unless otherwise specified.
Input Specifications
Parameters
Nominal
Typical
Maximum
Units
Voltage range
48
9-60
VDC
Filter
Capacitor
Absolute Maximum Rating
65
VDC
Peak Input Voltage time
500
ms
DC/DC ON (Leave open if not used)
ON –Open or 2.5V< Vadj <5V
DC/DC OFF (or short pins 2,3,4)
OFF(shutdown) – Vadj <0.8
Maximum Remote pin drive current
Vadj = 0 - 5V
<1
mA
Quiescent Current in Shutdown mode
Vin = 60V
3
mA
On/Off Control (Digital Control)
Max PWM Frequency 1KHz
Output current adjustment
1 to 100
%
Output Specifications
Parameters
Conditions
Typical
Maximum
Units
Current accuracy
±5
%
Output Voltage range
V input = 60V
2-56
VDC
Output current
Vin – Vout > 4V
Short Circuit protection
Temperature coefficient
Regulated at the rated current for each model
±0.03
%/^oC
General Specifications
Parameters
Conditions
Typical
Maximum
Switching frequency
100% load
40-1000
Operating temperature
See derating chart -40 to +85
Storage temperature
-40 to +125
Maximum case temperature
105
Thermal Impedance
Free air convection
+30
Cooling
Free air convection
Humidity
95
Case material
Non-Conductive Black Plastic (UL94V-0 rated)
Weight
17.7
Dimensions (L x W x H)
MTBF
1.25 x 0.80 x 0.49 inches
31.75 x 20.32 x 12.45 mm
> 2 000 000hrs (MIL-HDBK-217 F at +25 ^oC)
Maximum Soldering Temperature
1.5 mm from case for 10sec.
260
NOTES:
1. Reversed polarity at the input power will damage the driver. The input ground must not be connected to the negative output.
2. Maximum output open voltage is equal to input voltage.
Units
KHz
o_C
o_C
o_C
o_C/W
% RH
g
o_C
www.aimtec.com
F 051e R12.C
Tel: [phone]
1 of 3
Toll free: + 1 888 9 AIMTEC
(924 6832)
North America only