AMEPR60-AZ_16 Datasheet, PDF (1/14 Pages) AIMTEC – AC-DC Constant Current or Constant Voltage LED Driver

Click on Series name for product info on aimtec.com
Series AMEPR60-AZ
up to 5A | AC-DC / DC-DC | LED Driver / Converter
FEATURES:
 AC-DC Constant Current or Constant
Voltage LED Driver
 Over Temperature Protection
 Over Current Protection
 Input range 90-305VAC/47-440Hz
 Waterproof Case rated IP68
 High Efficiency up to 89%
 Power Factor Correction
 Operating temperature -40 to 85°C
 Short Circuit Protection
Models
Single output
 Dimmable via resistive / 0-10Vdc / PWM
 5 Years Limited Warranty
Model
Output
Voltage
Range
(V) ^③
Output
Current
(A) ^③
Input
Voltage
(VAC/Hz)
Input
Voltage
(VDC)
Mode of Operation
OCP /
OVP
Max
Output
Power
(W) ^①
Efficiency
(%)
AMEPR60-50120AZ
36-50
0 - 1.20
90-305 /
47-440
130-430
Constant Current
Constant Voltage ^②
1.27
50.7
60
63.8
89
86
AMEPR60-36170AZ
24-36
0 - 1.70
90-305 /
47-440
130-430
Constant Current
Constant Voltage ^②
1.77
36.6
59.8
63.7
88
86
AMEPR60-24250AZ
12-24
0 - 2.50
90-305 /
47-440
130-430
Constant Current
Constant Voltage ^②
2.55
24.5
60
61
87
85
AMEPR60-12500AZ
5-12
0 - 5.0
90-305 /
47-440
130-430
Constant Current
Constant Voltage ^②
5.2
12.3
60
62
85
82
① _{Exceeding the maximum output power will permanently damage the converter}
② _{The dimming feature is not supported when units are used in Constant Voltage mode only.}
③ _{In constant current mode output current is maximum shown, in constant voltage mode output voltage is the maximum shown.}
All models can be ordered with optional North American colour input wires (black (L), white (N), green (GND)). Add “–NA” to part number
when ordering.
Note: Aimtec limited warranty of 5 years is valid based on product operation at datasheet specifications at ambient temperature of 25°C,
humidity<75%, nominal input voltage (115/230/277VAC) and at rated output load unless otherwise specified. See
http://www.aimtec.com/terms-sale
AMEPR60-AZ’s AC/DC LED drivers have electrical safeguards designed within to protect it from conventional electrical abnormalities with
the levels listed in the safety table. Applications for use within rural agricultural, heavy industrial, and other areas or regions which are prone
to ‘dirty’ electrical conditions which would subject any of the above models to excessive voltages surges or spikes, may damage or cause
early life failure of product. In this case consideration should be made by the end user to ensure that adequate line or mains surge
suppression is installed in front of Aimtec device to ensure the longevity of the products. Failure to identify excessive line surges violations
prior to installation may damage sensitive equipment permanently.
Input Specifications
Parameters
Inrush current <2ms
Leakage current
AC current
Power Factor
External fuse
Start up time
Surge voltage
Conditions
115VAC
230VAC
115VAC
230VAC
115VAC
230VAC
115VAC
230VAC
2sec
Typical
30
50
0.5
0.7
0.73
0.33
250
Maximum
0.97
0.93
250V/1.5A
440
Units
A
mA
A
ms
V
www.aimtec.com
F 052.1e R3.AE
Tel: [phone]
1 of 14
Toll free: + 1 888 9 AIMTEC
(924 6832)
North America only