|
MIC-2718 Datasheet, PDF (1/1 Pages) Advantech Co., Ltd. – 16-Channel Analog Input Module | |||
|
MIC
MIC-2718
MIC-2728
MIC-2730
16-Channel Analog Input Module
4-Channel Isolated Analog Output Module
16-Channel Isolated Digital Input Module
MIC-2718
16-Channel Analog Input
Module
The MIC-2718 offers multiple, high-
speed data acquisition functions. It is a
cost effective solution for industrial
measurement and monitoring.
⢠Channels: 16 single-ended or 8
differential, switch selectable
⢠A/D converter:
12-bit, 8 µsec. max. conversion time
⢠On-board FIFO: 1 K words
⢠Input range (software programmable):
Bipolar: ±0.005, ±0.01, ±0.05, ±0.1,
±0.5, ±1, ±5, ±10 V
Unipolar: 0 to 0.01, 0 to 0.1, 0 to 1,0
to 10 V
⢠Overvoltage: ±30 V max.
⢠Maximum data throughput: 100 kHz
(depends on input amplifier settling
time and slew rate)
Gain
Speed
0.5, 1
100 kHz
5, 10
35 kHz
50, 100
7 kHz
500,1000
0.8 kHz
⢠Accuracy:
Gain=0.5, 1 0.01% of FSR ±1LSB
Gain=5, 10 0.02% of FSR ±1LSB
Gain=50,100 0.04% of FSR ±1LSB
Gain=500,1000 0.08% of FSR ±1LSB
⢠Linearity: ±1-bit
⢠Trigger mode:
Software, pacer or external
⢠Ext. trigger: TTL compatible
⢠Data transfer:
Program, interrupt or DMA
⢠Signal conditioning circuit: Space for
RC filter and 250 ⦠current shunt
⢠Power consumption: +5 V @ 0.5 A
max.; +12 V @ 0.2 A max.
MIC-2728
4-Channel Isolated
Analog Output Module
The MIC-2728 provides four double-
buffered 12-bit D/A outputs. Over 500
VDC of bus isolation protect your PC and
peripherals from dangerous output
voltages.
⢠Channels: 4 isolated D/A channels
⢠Resolution: 12-bits, double buffered
⢠Output range:
Unipolar: 0 to +5 V, 0 to +10 V
Bipolar: ±5 V, ±10 V
Current loop (sink);
0 to 20 mA, 4 to 20 mA
⢠Settling time::⤠60 µseconds
⢠Accuracy: ±0.012% FS
⢠Isolation voltage:
> 500 VDC bus isolation
⢠Reference voltage:
Internal: -5 V or -10 V
External: ±10 V max. AC or DC
⢠Voltage output drive: ±10 mA max.
⢠Current loop excitation: 8 V to 36 V
⢠Power consumption:
+5 V @ 0.5 A max.;
+12 V @ 0.2 A max.
MIC-2730
16-Channel Isolated
Digital Input Module
The MIC-2730 features a limit switch,
alarms and/or sensors for noisy
environments, and 16 optically isolated
digital input channels for monitoring
device On/Off status.
⢠Number of inputs: 16
⢠Input mode: isolated or non-isolated
(jumper selection)
Isolated Inputs
⢠Number of commons: 2 (isolated)
⢠Input voltage: 0 ~ 30 V
⢠Threshold voltage:
Logic "0" : < 1 V
Logic "1" : > 4 V
⢠Input impedance: 2 kâ¦
⢠Isolation voltage: 2500 V
DC
⢠Throughput: 10 kHz
Non-isolated Inputs (TTL-level)
⢠Input voltage:
Low: 0.8 V max.
High: 2.0 V min.
⢠Input load:
Low: 0.4 mA max @ 0.5 V
High: 0.05 mA max @ 2.7 V
⢠Pull-up resistor:
10 k⦠for dry contact
⢠Throughput: 30 kHz typical
⢠Number of indicator LEDs: 16
⢠Indication mode:
Logic â1â : LED On
Logic â0â : LED Off
⢠Power consumption: +5 V @ 2 A
11
MIC-2000 Series
Note: All specifications are subject to change without notice
11-9
|