AMAX-1220_15 Datasheet, PDF (1/1 Pages) Advantech Co., Ltd. – Open Frame Type 2/ 4-axis AMONet Motion Slave Modules

AMAX-1220
AMAX-1240
NEW
Open Frame Type 2/ 4-axis AMONet
Motion Slave Modules
Features
ƒƒ End limit logic is switchable (high or low active)
ƒƒ BoardID is switchable
ƒƒ Easily visible LED indicators on board to do diagnosis
ƒƒ Direct wire to servo drive to save terminal board space while installation
ƒƒ Max. 6.5 MHz, 4-axis pulse output
ƒƒ 28 bits counter for incremental encoder
ƒƒ Horizontal installation for for servo or stepping motor driver
ƒƒ Suitable for DIN-rail mounting
AMAX-1220
AMAX-1240
RoHS
COMPLIANT
2002/95/EC
Introduction
AMAX-1220 and AMAX-1240 have compact open frame designs for horizontal placement and an interface connector mounted on the board. With a transfer cable to servo drive, both
models can conveniently connect to Mitsubishi J3, Yaskwa Sigma V and Panasonic A4/A5.
The AMAX-1220 is an economic 2-axis AMONet slave module which supports motion functionality in point-to-point (PTP), linear & circular interpolation, simultaneously start/
stop among multiple slave modules, and brake signal to servo for emergence consideration. The AMAX-1240 is an advanced 4-axis AMONet slave module which not only supports
AMAX-1220 motion functionality, but also supports advanced features in position compare and triggering function. Both linear interval and table setups are supported.
Specifications
Pulse Type Motion Control
ƒƒ Motor Driver Support Pulse-type servo
ƒƒ Number of Axes
AMAX-1220: 2
AMAX-1240: 4
ƒƒ Interpolation
Linear and circular
ƒƒ Max. Output Speed 6.5 Mpps
ƒƒ Step Count Range
±134, 217, 728
ƒƒ Pulse Output Type
OUT/DIR, CW/CCW, A/B phase
ƒƒ Position Counter
±134, 217, 728
ƒƒ Home Modes
13
ƒƒ Velocity Profiles
T-Curve, S-Curve
ƒƒ Local I/O
Machine Interfaces:
EL+/-, ORG and SD (Slow Down) for Each Axis
Servo Driver Interfaces: ALM, RDY, SVON, INP, Break for Each Axis
Position Compare I/O:
LTC, CMP for Each Axis(Only available for
AMAX-1240-AE)
Simultaneous Move Within
Multiple Modules:
General Purpose I/O:
CSTA/CSTP (Simultaneously Start/Stop) for
each model
AMAX-1220 supports 8xDI and 8xDO
Encoder Interface
ƒƒ Input Type
ƒƒ Counts per Enc. Cycle
ƒƒ Input Range
ƒƒ Isolation Protection
ƒƒ Max. Input Frequency
A/B phase, CW/CCW
x1, x2, x4 (AB phase only)
Low: 0 ~ 0.5V
High: 3.5 ~ 7V
2,500 VRMS
2 MHz @ 5 V
General
ƒƒ Bus Type
AMONet RS-485
ƒƒ Certification
CE, FCC Class A
ƒƒ Connectors
RJ-45 x 2 are for communication port
DB-26 connector by transfer cable to servo
drives. Other are screw terminal type connectors
ƒƒ Dimensions (L x W x H) 141 x 108 x 60 mm (5.6" x 4.3" x 2.4")
ƒƒ System Power
Consumption
2 W @ 24 V typical
Output Channel Power
Consumption
120W typical, 240W max.
Input Channel Power
Consumption
AMAX-1220: 8 W @ 24 V external power (max.)
AMAX-1240: 10 W @ 24 V external power (max.)
ƒƒ System Power Input 24 VDC within 200 mV ripple
ƒƒ Humidity
5 ~ 95% RH, non-condensing (IEC 60068-2-3)
ƒƒ Operating Temperature 0 ~ 60°C (32 ~ 140°F)
Ordering Information
ƒƒ AMAX-1220-AE
ƒƒ AMAX-1240-AE
Economic 2-axis AMONet Motion Control Module
Advanced 4-axis AMONet Motion Control Module
Accessories
ƒƒ PCL-10153PA5-2E
ƒƒ PCL-10153PA5LS-2E
ƒƒ PCL-10153YS5-2E
ƒƒ PCL-10153MJ3-2E
ƒƒ ●PCL-10153DA2-2E
50-pin Cable to Panasonic A4 and A5 Servo, 2 m
50-pin Cable to Panasonic MINAS A Servo, 2 m
50-pin Cable to Yaskawa Sigma V Servo, 2 m
50-pin Cable to Mitsubishi J3 Servo, 2 m
50-pin Cable from ADAM-3955/ADAM-3956 to Delta
A2 Servo, 2 m
All product specifications are subject to change without notice
Online Download www.advantech.com/products
Last updated : 5-May-2015