APT5510B2FLL Datasheet, PDF (2/5 Pages) Advanced Power Technology – POWER MOS 7 FREDFET

DYNAMIC CHARACTERISTICS
APT5510B2FLL - LFLL
Symbol Characteristic
Test Conditions
MIN TYP MAX UNIT
C_iss
C_oss
C_rss
Input Capacitance
Output Capacitance
Reverse Transfer Capacitance
V_GS = 0V
V_DS = 25V
f = 1 MHz
5823
1124
pF
81
Q_g
Total Gate Charge ³
Q_{gs Gate-Source Charge}
Q_{gd Gate-Drain ("Miller") Charge}
V_GS = 10V
V_DD = 275V
I_D = 49A @ 25°C
124
34
nC
64
t_d(on)
t_r
t_d(off)
t_f
E_on
E_off
E_on
E_off
Turn-on Delay Time
Rise Time
Turn-off Delay Time
Fall Time
Turn-on Switching Energy ⁶
Turn-off Switching Energy
Turn-on Switching Energy ⁶
Turn-off Switching Energy
RESISTIVE SWITCHING
16
V_GS = 15V
V_DD = 275V
I_D = 49A @ 25°C
12
ns
33
R_G = 0.6Ω
5
INDUCTIVE SWITCHING @ 25°C
V_DD = 367V, V_GS = 15V
697
I_D = 49A, R_G = 5Ω
577
µJ
INDUCTIVE SWITCHING @ 125°C
1025
V_DD = 367V V_GS = 15V
I_D = 49A, R_G = 5Ω
664
SOURCE-DRAIN DIODE RATINGS AND CHARACTERISTICS
Symbol Characteristic / Test Conditions
MIN TYP MAX UNIT
I_S
Continuous Source Current (Body Diode)
I_{SM Pulsed Source Current} 1 _{(Body Diode)}
49 _Amps
196
V_{SD Diode Forward Voltage} 2 _{(VGS = 0V, IS = -49A)}
dv_/dt
Peak Diode Recovery ^dv/_dt ⁵
1.3 Volts
15 V/ns
t_rr
Reverse Recovery Time
(I_S = -49A, ^di/_dt = 100A/µs)
T_j = 25°C
T_j = 125°C
260
ns
600
Reverse Recovery Charge
Q_rr
(I_S = -49A, ^di/_dt = 100A/µs)
T_j = 25°C
T_j = 125°C
1.9
µC
5.7
Peak Recovery Current
I_RRM
(I_S = -49A, ^di/_dt = 100A/µs)
T_j = 25°C
T_j = 125°C
15
Amps
23
THERMAL CHARACTERISTICS
Symbol Characteristic
MIN TYP MAX UNIT
R_θJC
R_θJA
Junction to Case
Junction to Ambient
0.22
40
°C/W
1 Repetitive Rating: Pulse width limited by maximum junction
temperature
2 Pulse Test: Pulse width < 380 µs, Duty Cycle < 2%
3 See MIL-STD-750 Method 3471
4 Starting T_j = +25°C, L = 2.08mH, R_G = 25Ω, Peak I_L = 49A
5 ^dv/_dt numbers reflect the limitations of the test circuit rather than the
device itself. I_S ≤ -I_D49A ^di/_dt ≤ 700A/µs V_R ≤ V_DSS T_J ≤ 150°C
6 Eon includes diode reverse recovery. See figures 18, 20.
APT Reserves the right to change, without notice, the specifications and information contained herein.
0.25
0.20
0.9
0.7
0.15
0.10
0.05
0 _10-5
0.5
Note:
t1
0.3
t2
0.1
0.05
SINGLE PULSE
Duty Factor D = ^t1/t2
Peak TJ = PDM x Z_θJC + TC
10^-4
10^-3
10^-2
10^-1
1.0
RECTANGULAR PULSE DURATION (SECONDS)
FIGURE 1, MAXIMUM EFFECTIVE TRANSIENT THERMAL IMPEDANCE, JUNCTION-TO-CASE vs PULSE DURATION