APT30M17JFLL Datasheet, PDF (2/5 Pages) Advanced Power Technology – POWER MOS 7 FREDFET

DYNAMIC CHARACTERISTICS
APT30M17JFLL
Symbol Characteristic
Test Conditions
C_iss
C_oss
C_rss
Q_g
Q_gs
Q_gd
t_d(on)
t_r
t_d(off)
t_f
E_on
E_off
E_on
E_off
Input Capacitance
Output Capacitance
Reverse Transfer Capacitance
Total Gate Charge ³
Gate-Source Charge
Gate-Drain ("Miller") Charge
Turn-on Delay Time
Rise Time
Turn-off Delay Time
Fall Time
Turn-on Switching Energy ⁶
Turn-off Switching Energy
Turn-on Switching Energy ⁶
Turn-off Switching Energy
V_GS = 0V
V_DS = 25V
f = 1 MHz
V_GS = 10V
V_DD =150V
I_D = 135A @ 25°C
RESISTIVE SWITCHING
V_GS = 15V
V_DD = 150V
I_D = 135A @ 25°C
R_G = 0.6Ω
INDUCTIVE SWITCHING @ 25°C
V_DD = 200V, V_GS = 15V
I_D = 100A, R_G = 5Ω
INDUCTIVE SWITCHING @ 125°C
V_DD = 200V, V_GS = 15V
I_D = 100A, R_G = 5Ω
SOURCE-DRAIN DIODE RATINGS AND CHARACTERISTICS
Symbol Characteristic / Test Conditions
MIN TYP MAX UNIT
14100
3285
pF
185
230
85
nC
105
19
31
ns
44
13
1120
1250
µJ
1325
1460
MIN TYP MAX UNIT
I_S
Continuous Source Current (Body Diode)
I_{SM Pulsed Source Current} 1 _{(Body Diode)}
V_{SD Diode Forward Voltage} ² _{(VGS = 0V, IS = -135A)}
dv_{/dt Peak Diode Recovery} dv_/dt 5
Reverse Recovery Time
t_rr
(I_S = -135A, ^di/_dt = 100A/µs)
Reverse Recovery Charge
Q_rr
(I_S = -135A, ^di/_dt = 100A/µs)
I_RRM
Peak Recovery Current
(I_S = -135A, ^di/_dt = 100A/µs)
T_j = 25°C
T_j = 125°C
T_j = 25°C
T_j = 125°C
T_j = 25°C
T_j = 125°C
135 _Amps
540
1.3 Volts
8
V/ns
200 300
ns
250 525
1.5
µC
4.4
15
Amps
25
THERMAL CHARACTERISTICS
Symbol Characteristic
MIN TYP MAX UNIT
R_θJC
R_θJA
Junction to Case
Junction to Ambient
0.18
40
°C/W
1 Repetitive Rating: Pulse width limited by maximum junction
temperature
2 Pulse Test: Pulse width < 380 µs, Duty Cycle < 2%
3 See MIL-STD-750 Method 3471
4 Starting T_j = +25°C, L = .40mH, R_G = 25Ω, Peak I_L = 135A
5 ^dv/_dt numbers reflect the limitations of the test circuit rather than the
device itself. I_S ≤ I_D-135A ^di/_dt ≤ 700A/µs V_R ≤ 300 T_J ≤ 150°C
6 Eon includes diode reverse recovery. See figures 18, 20.
APT Reserves the right to change, without notice, the specifications and inforation contained herein.
0.20
0.9
0.16
0.7
0.12
0.08
0.04
0
10^-5
0.5
Note:
0.3
t1
0.1
0.05
SINGLE PULSE
t2
Duty Factor D = ^t1/t2
Peak TJ = PDM x Z_θJC + TC
10^-4
10^-3
10^-2
10^-1
1.0
10
RECTANGULAR PULSE DURATION (SECONDS)
FIGURE 1, MAXIMUM EFFECTIVE TRANSIENT THERMAL IMPEDANCE, JUNCTION-TO-CASE vs PULSE DURATION