OP284_15 Datasheet, PDF (5/24 Pages) Analog Devices – Precision Rail-to-Rail Input and Output Operational Amplifiers

OP184/OP284/OP484
VS = ±15.0 V, VCM = 0 V, TA = 25°C, unless otherwise noted.
Table 4.
Parameter
INPUT CHARACTERISTICS
Offset Voltage, OP184/OP284E Grade¹
Offset Voltage, OP184/OP284F Grade¹
Offset Voltage, OP484E Grade¹
Offset Voltage, OP484F Grade¹
Input Bias Current
Input Offset Current
Input Voltage Range
Common-Mode Rejection Ratio
Large Signal Voltage Gain
Offset Voltage Drift E Grade
Bias Current Drift
OUTPUT CHARACTERISTICS
Output Voltage High
Output Voltage Low
Output Current
POWER SUPPLY
Power Supply Rejection Ratio
Supply Current/Amplifier
Supply Current/Amplifier
DYNAMIC PERFORMANCE
Slew Rate
Full-Power Bandwidth
Settling Time
Gain Bandwidth Product
Phase Margin
NOISE PERFORMANCE
Voltage Noise
Voltage Noise Density
Current Noise Density
Symbol Conditions
VOS
−40°C ≤ TA ≤ +125°C
VOS
−40°C ≤ TA ≤ +125°C
VOS
−40°C ≤ TA ≤ +125°C
VOS
−40°C ≤ TA ≤ +125°C
IB
−40°C ≤ TA ≤ +125°C
IOS
−40°C ≤ TA ≤ +125°C
CMRR
AVO
ΔVOS/ΔT
ΔVB/ΔT
VCM = −14.0 V to +14.0 V, −40°C ≤ TA ≤ +125°C
VCM = −15.0 V to +15.0 V
RL = 2 kΩ, −10 V ≤ VO ≤ 10 V
RL = 2 kΩ, −40°C ≤ TA ≤ +125°C
VOH
IL = 1.0 mA
VOL
IL = 1.0 mA
IOUT
PSRR
ISY
ISY
VS = ±2.0 V to ±18 V, −40°C ≤ TA ≤ +125°C
VO = 0 V, −40°C ≤ TA ≤ +125°C
VS = ±18 V, −40°C ≤ TA ≤ +125°C
SR
RL = 2 kΩ
BWp
1% distortion, RL = 2 kΩ, VO = 29 V p-p
tS
To 0.01%, 10 V step
GBP
ΦM
en p-p
en
in
0.1 Hz to 10 Hz
f = 1 kHz
Min Typ Max
Unit
100
200
175
375
150
300
250
500
80 450
575
50
−15
+15
86 90
80
150 1000
75
0.2 2.00
150
μV
μV
μV
μV
μV
μV
μV
μV
nA
nA
nA
V
dB
dB
V/mV
V/mV
μV/°C
pA/°C
14.8
V
−14.875 V
±10
mA
90
dB
2.0
mA
2.25
mA
2.4 4.0
35
4
4.25
50
V/µs
kHz
µs
MHz
Degrees
0.3
µV p-p
3.9
nV/√Hz
0.4
pA/√Hz
1 _{Input offset voltage measurements are performed by automated test equipment approximately 0.5 seconds after application of power.}
Rev. J | Page 5 of 24