ADG811YRUZ Datasheet, PDF (5/16 Pages) Analog Devices – 0.5ohm CMOS, 1.65 V to 3.6 V, Quad SPST Switches

ADG811/ADG812/ADG813
VDD = 1.65 V to 1.95 V, GND = 0 V, unless otherwise noted. Temperature range for the Y version is −40°C to +125°C.
Table 3.
Parameter
ANALOG SWITCH
Analog Signal Range
On Resistance, RON
On Resistance Match Between
Channels, ΔRON
LEAKAGE CURRENTS
Source Off Leakage IS (Off )
Drain Off Leakage ID (Off )
Channel On Leakage ID, IS (On)
DIGITAL INPUTS
Input High Voltage, VINH
Input Low Voltage, VINL
Input Current, IINL or IINH
CIN, Digital Input Capacitance
DYNAMIC CHARACTERISTICS¹
tON
tOFF
Break-Before-Make Time Delay, tBBM
(ADG813 Only)
Charge Injection
Off Isolation
Channel-to-Channel Crosstalk
Total Harmonic Distortion (THD + N)
Insertion Loss
–3 dB Bandwidth
CS (Off )
CD (Off )
CD, CS (On)
POWER REQUIREMENTS
IDD
+25°C
1
1.4
2.5
0.1
±0.2
±1
±0.2
±1
±0.2
±1
0.005
6
27
35
6
8
20
15
−67
−90
0.14
−0.08
90
32
38
60
0.003
−40°C to +85°C
2.2
4
±5
±5
±9
36
9
1.0
−40°C to +125°C
0 V to VDD
2.2
4
±30
±30
±60
0.65VDD
0.35VDD
±0.1
37
10
5
4
Unit
V
Ω typ
Ω max
Ω max
Ω typ
nA typ
nA max
nA typ
nA max
nA typ
nA max
V min
V max
μA typ
μA max
pF typ
ns typ
ns max
ns typ
ns max
ns typ
ns min
pC typ
dB typ
dB typ
%
dB typ
MHz typ
pF typ
pF typ
pF typ
μA typ
μA max
Test Conditions/Comments
VDD = 1.8 V, VS = 0 V to VDD, IS = 10 mA;
see Figure 19
VDD = 1.65 V, VS = 0 V to VDD, IS = 10 mA
VDD = 1.65 V, VS = 0.7 V, IS = 10 mA
VDD = 1.95 V
VS = 0.6 V/1.65 V, VD = 1.65 V/0.6 V;
see Figure 20
VS = 0.6 V/1.65 V, VD = 1.65 V/0.6 V;
see Figure 20
VS = VD = 0.6 V or 1.65 V; see Figure 21
VIN = VINL or VINH
RL = 50 Ω, CL = 35 pF
VS = 1.5 V/ 0 V; see Figure 22
RL = 50 Ω, CL = 35 pF
VS = 1.5 V; see Figure 22
RL = 50 Ω, CL = 35 pF
VS1 = VS2 = 1 V; see Figure 23
VS = 1 V, RS = 0 Ω, CL = 1 nF;
see Figure 24
RL = 50 Ω, CL = 5 pF, f = 100 kHz;
Figure 25
RL = 50 Ω, CL = 5 pF, f = 100 kHz;
see Figure 27
RL = 32 Ω, f = 20 Hz to 20 kHz,
VS = 1.2 V p-p
RL = 50 Ω, CL = 5 pF, f = 100 kHz
RL = 50 Ω, CL = 5 pF; see Figure 26
VDD = 1.95 V
Digital inputs = 0 V or 1.95 V
1 _{Guaranteed by design, but not subject to production test.}
Rev. B | Page 5 of 16