ADG5233 Datasheet, PDF (5/24 Pages) Analog Devices – High Voltage Latch-Up Proof

Data Sheet
ADG5233/ADG5234
Parameter
CS (Off )
CD (Off )
CD (On), CS (On)
POWER REQUIREMENTS
IDD
ISS
VDD/VSS
25°C
4.5
10
15
50
70
0.001
−40°C to +85°C
−40°C to +125°C
110
1
±9/±22
Unit
pF typ
pF typ
pF typ
µA typ
µA max
µA typ
µA max
V min/V max
Test Conditions/Comments
VS = 0 V, f = 1 MHz
VS = 0 V, f = 1 MHz
VS = 0 V, f = 1 MHz
VDD = +22 V, VSS = −22 V
Digital inputs = 0 V or VDD
Digital inputs = 0 V or VDD
GND = 0 V
1 _{Guaranteed by design; not subject to production test.}
12 V SINGLE SUPPLY
VDD = 12 V ± 10%, VSS = 0 V, GND = 0 V, unless otherwise noted.
Table 3.
Parameter
ANALOG SWITCH
Analog Signal Range
On Resistance, RON
25°C −40°C to +85°C −40°C to +125°C Unit
0 V to VDD
V
360
Ω typ
500 610
700
On-Resistance Match Between 5.5
Channels, ∆RON
20 21
22
On-Resistance Flatness, RFLAT (ON) 170
280 335
370
LEAKAGE CURRENTS
Source Off Leakage, IS (Off )
±0.02
Ω max
Ω typ
Ω max
Ω typ
Ω max
nA typ
±0.1 ±0.2
±0.4
Drain Off Leakage, ID (Off )
±0.02
nA max
nA typ
±0.1 ±0.2
±0.4
Channel On Leakage, ID (On), IS (On) ±0.08
±0.2 ±0.3
±0.9
DIGITAL INPUTS
Input High Voltage, VINH
2.0
Input Low Voltage, VINL
0.8
Input Current, IINL or IINH
0.002
±0.1
Digital Input Capacitance, CIN
3
DYNAMIC CHARACTERISTICS¹
Transition Time, tTRANSITION
235
295 365
410
tON (EN)
240
305 380
430
tOFF (EN)
70
90 105
115
Break-Before-Make Time Delay, tD 125
65
Charge Injection, QINJ
0
nA max
nA typ
nA max
V min
V max
µA typ
µA max
pF typ
ns typ
ns max
ns typ
ns max
ns typ
ns max
ns typ
ns min
pC typ
Test Conditions/Comments
VS = 0 V to 10 V, IS = −1 mA; see
Figure 26
VDD = 10.8 V, VSS = 0 V
VS = 0 V to 10 V, IS = −1 mA
VS = 0 V to 10 V, IS = −1 mA
VDD = 13.2 V, VSS = 0 V
VS = 1 V/10 V, VD = 10 V/1 V; see
Figure 28
VS = 1 V/10 V, VD = 10 V/1 V; see
Figure 28
VS = VD = 1 V/10 V; see Figure 25
VIN = VGND or VDD
RL = 300 Ω, CL = 35 pF
VS = 8 V; see Figure 31
RL = 300 Ω, CL = 35 pF
VS = 8 V; see Figure 33
RL = 300 Ω, CL = 35 pF
VS = 8 V; see Figure 33
RL = 300 Ω, CL = 35 pF
VS1 = VS2 = 8 V; see Figure 32
VS = 6 V, RS = 0 Ω, CL = 1 nF; see
Figure 34
Rev. A | Page 5 of 24