ADG1604 Datasheet, PDF (5/20 Pages) Analog Devices – 1 Ω Typical On Resistance, ±5 V, +12 V, +5 V, and +3.3 V, 4:1 Multiplexer

ADG1604
5 V SINGLE SUPPLY
VDD = 5 V ± 10%, VSS = 0 V, GND = 0 V, unless otherwise noted.
Table 3.
Parameter
ANALOG SWITCH
Analog Signal Range
On Resistance (RON)
On Resistance Match Between Channels (∆RON)
On Resistance Flatness (RFLAT(ON))
LEAKAGE CURRENTS
Source Off Leakage, IS (Off )
Drain Off Leakage, ID (Off )
Channel On Leakage, ID, IS (On)
DIGITAL INPUTS
Input High Voltage, VINH
Input Low Voltage, VINL
Input Current, IINL or IINH
Digital Input Capacitance, CIN
DYNAMIC CHARACTERISTICS¹
Transition Time, tTRANSITION
tON (EN)
tOFF (EN)
Break-Before-Make Time Delay, tD
Charge Injection
Off Isolation
Channel-to-Channel Crosstalk
Total Harmonic Distortion + Noise
−3 dB Bandwidth
CS (Off )
CD (Off )
CD, CS (On)
POWER REQUIREMENTS
IDD
VDD
25°C
1.7
2.15
0.05
0.09
0.4
0.53
±0.05
±0.2
±0.05
±0.2
±0.1
±0.4
0.001
8
175
283
135
174
228
288
30
70
70
70
0.09
16
70
300
400
0.001
−40°C to
+85°C
2.4
0.12
0.55
±1
±2
±2
337
194
342
−40°C to
+125°C
0 V to VDD
2.7
0.15
0.6
±8
±16
±16
2.0
0.8
±0.1
380
212
385
21
1
3.3/16
Unit
V
Ω typ
Ω max
Ω typ
Ω max
Ω typ
Ω max
nA typ
nA max
nA typ
nA max
nA typ
nA max
V min
V max
μA typ
μA max
pF typ
ns typ
ns max
ns typ
ns max
ns typ
ns max
ns typ
ns min
pC typ
dB typ
dB typ
% typ
MHz typ
pF typ
pF typ
pF typ
μA typ
μA max
V min/max
Test Conditions/Comments
VS = 0 V to 4.5 V, IS = −10 mA; see Figure 22
VDD = 4.5 V, VSS = 0 V
VS = 0 V to 4.5 V, IS = −10 mA
VS = 0 V to 4.5 V, IS = −10 mA
VDD = 5.5 V, VSS = 0 V
VS = 1 V/4.5 V, VD = 4.5 V/1 V; see Figure 23
VS = 1 V/4.5 V, VD = 4.5 V/1 V; see Figure 23
VS = VD = 1 V or 4.5 V; see Figure 24
VIN = VGND or VDD
RL = 300 Ω, CL = 35 pF
VS = 2.5 V; see Figure 29
RL = 300 Ω, CL = 35 pF
VS = 2.5 V; see Figure 31
RL = 300 Ω, CL = 35 pF
VS = 2.5 V; see Figure 31
RL = 300 Ω, CL = 35 pF
VS1 = VS2 = 2.5 V; see Figure 30
VS = 2.5 V, RS = 0 Ω, CL = 1 nF; see Figure 32
RL = 50 Ω, CL = 5 pF, f = 100 kHz;
see Figure 25
RL = 50 Ω, CL = 5 pF, f = 100 kHz;
see Figure 27
RL = 110 Ω, f = 20 Hz to 20 kHz, VS = 3.5 V p-p;
see Figure 28
RL = 50 Ω, CL = 5 pF; see Figure 26
VS = 2.5 V, f = 1 MHz
VS = 2.5 V, f = 1 MHz
VS = 2.5 V, f = 1 MHz
VDD = 5.5 V
Digital inputs = 0 V or VDD
1 _{Guaranteed by design, not subject to production test.}
Rev. 0 | Page 5 of 20