ADUC7019_13 Datasheet, PDF (41/104 Pages) Analog Devices – Precision Analog Microcontroller, 12-Bit Analog I/O, ARM7TDMI MCU

Data Sheet
MEMORY ORGANIZATION
The ADuC7019/20/21/22/24/25/26/27/28/29 incorporate two
separate blocks of memory: 8 kB of SRAM and 64 kB of on-chip
Flash/EE memory. The 62 kB of on-chip Flash/EE memory is
available to the user, and the remaining 2 kB are reserved for
the factory-configured boot page. These two blocks are mapped
as shown in Figure 45.
0xFFFFFFFF
0xFFFF0000
MMRs
RESERVED
0x40000FFFF
0x40000000
EXTERNAL MEMORY REGION 3
RESERVED
0x30000FFFF
0x30000000
EXTERNAL MEMORY REGION 2
RESERVED
0x20000FFFF
0x20000000
EXTERNAL MEMORY REGION 1
RESERVED
0x10000FFFF
0x10000000
EXTERNAL MEMORY REGION 0
RESERVED
0x0008FFFF
0x00080000
FLASH/EE
RESERVED
0x00011FFF
0x00010000
SRAM
0x0000FFFF REMAPPABLE MEMORY SPACE
0x00000000
(FLASH/EE OR SRAM)
Figure 45. Physical Memory Map
Note that by default, after a reset, the Flash/EE memory is
mirrored at Address 0x00000000. It is possible to remap the
SRAM at Address 0x00000000 by clearing Bit 0 of the REMAP
MMR. This remap function is described in more detail in the
Flash/EE Memory section.
MEMORY ACCESS
The ARM7 core sees memory as a linear array of a 2³² byte
location where the different blocks of memory are mapped as
outlined in Figure 45.
The ADuC7019/20/21/22/24/25/26/27/28/29 memory organiza-
tions are configured in little endian format, which means that
the least significant byte is located in the lowest byte address,
and the most significant byte is in the highest byte address.
BIT 31
BIT 0
BYTE 3
.
.
.
BYTE 2
.
.
.
BYTE 1
.
.
.
BYTE 0
.
.
.
0xFFFFFFFF
B
A
9
8
7
6
5
4
3
2
1
0
0x00000004
0x00000000
32 BITS
Figure 46. Little Endian Format
ADuC7019/20/21/22/24/25/26/27/28/29
FLASH/EE MEMORY
The total 64 kB of Flash/EE memory is organized as 32 k × 16 bits;
31 k × 16 bits is user space and 1 k × 16 bits is reserved for the
on-chip kernel. The page size of this Flash/EE memory is 512 bytes.
Sixty-two kilobytes of Flash/EE memory are available to the
user as code and nonvolatile data memory. There is no
distinction between data and program because ARM code
shares the same space. The real width of the Flash/EE memory
is 16 bits, which means that in ARM mode (32-bit instruction),
two accesses to the Flash/EE are necessary for each instruction
fetch. It is therefore recommended to use thumb mode when
executing from Flash/EE memory for optimum access speed.
The maximum access speed for the Flash/EE memory is
41.78 MHz in thumb mode and 20.89 MHz in full ARM mode.
More details about Flash/EE access time are outlined in the
Execution Time from SRAM and Flash/EE section.
SRAM
Eight kilobytes of SRAM are available to the user, organized as
2 k × 32 bits, that is, two words. ARM code can run directly
from SRAM at 41.78 MHz, given that the SRAM array is
configured as a 32-bit wide memory array. More details about
SRAM access time are outlined in the Execution Time from
SRAM and Flash/EE section.
MEMORY MAPPED REGISTERS
The memory mapped register (MMR) space is mapped into the
upper two pages of the memory array and accessed by indirect
addressing through the ARM7 banked registers.
The MMR space provides an interface between the CPU and all
on-chip peripherals. All registers, except the core registers, reside
in the MMR area. All shaded locations shown in Figure 47 are
unoccupied or reserved locations and should not be accessed by
user software. Table 16 shows the full MMR memory map.
The access time for reading from or writing to an MMR
depends on the advanced microcontroller bus architecture
(AMBA) bus used to access the peripheral. The processor has
two AMBA buses: the advanced high performance bus (AHB)
used for system modules and the advanced peripheral bus
(APB) used for lower performance peripheral. Access to the
AHB is one cycle, and access to the APB is two cycles. All
peripherals on the ADuC7019/20/21/22/24/25/26/27/28/29 are
on the APB except the Flash/EE memory, the GPIOs (see
Table 78), and the PWM.
Rev. F | Page 41 of 104