DAC8248FS Datasheet, PDF (4/16 Pages) Analog Devices – Dual 12-Bit (8-Bit Byte) Double-Buffered CMOS D/A Converter

DAC8248
(continued from page 1)
operates on a single supply from +5 V to +15 V, and it dissi-
pates less than 0.5 mW at +5 V (using zero or V_DD logic levels).
The device is packaged in a space-saving 0.3", 24-pin DIP.
The DAC8248 is manufactured with PMI’s highly stable thin-
film resistors on an advanced oxide-isolated, silicon-gate,
CMOS technology. PMI’s improved latch-up resistant design
eliminates the need for external protective Schottky diodes.
Package Type
␪_JA1
␪_JC
Units
24-Pin Hermetic DIP (W)
69
24-Pin Plastic DIP (P)
62
24-Pin SOL (S)
72
10
°C/W
32
°C/W
24
°C/W
NOTE
1_{␪JA specified for worst case mounting conditions, i.e., ␪JA is specified for device in}
socket for cerdip and P-DIP packages; ␪_JA is specified for device soldered to printed
circuit board for SOL package.
ABSOLUTE MAXIMUM RATINGS
(T_A = +25°C, unless otherwise noted.)
V_DD to AGND . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0 V, +17 V
V_DD to DGND . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0 V, +17 V
AGND to DGND . . . . . . . . . . . . . . . . . . –0.3 V, V_DD +0.3 V
Digital Input Voltage to DGND . . . . . . . –0.3 V, V_DD +0.3 V
I_{OUT A}, I_{OUT B} to AGND . . . . . . . . . . . . . . –0.3 V, V_DD +0.3 V
V_{REF A}, V_{REF B} to AGND . . . . . . . . . . . . . . . . . . . . . . . . ± 25 V
V_{RFB A}, V_{RFB B} to AGND . . . . . . . . . . . . . . . . . . . . . . . . ± 25 V
Operating Temperature Range
AW Version . . . . . . . . . . . . . . . . . . . . . . . –55°C to +125°C
EW, FW, FP Versions . . . . . . . . . . . . . . . . –40°C to +85°C
GP, HP, HS Versions . . . . . . . . . . . . . . . . . . . 0°C to +70°C
Junction Temperature . . . . . . . . . . . . . . . . . . . . . . . . +150°C
Storage Temperature . . . . . . . . . . . . . . . . . . –65°C to +150°C
Lead Temperature (Soldering, 60 sec) . . . . . . . . . . . . +300°C
CAUTION
1. Do not apply voltages higher than V_DD or less than GND
potential on any terminal except V_REF and R_FB.
2. The digital control inputs are Zener-protected; however,
permanent damage may occur on unprotected units from
high energy electrostatic fields. Keep units in conductive
foam at all times until ready to use.
3. Do not insert this device into powered sockets; remove
power before insertion or removal.
4. Use proper antistatic handling procedures.
5. Devices can suffer permanent damage and/or reliability deg-
radation if stressed above the limits listed under Absolute
Maximum Ratings for extended periods. This is a stress rat-
ing only and functional operation at or above this specifica-
tion is not implied.
ORDERING GUIDE¹
Model
Relative
Accuracy
Gain Error
Temperature
(+5 V or +15 V) (+5 V or +15 V) Range
Package
Description
DAC8248AW²
DAC8248EW
DAC8248GP
DAC8248FW
DAC8248HP
DAC8248FP
DAC8248HS³
± 1/2 LSB
± 1/2 LSB
± 1/2 LSB
± 1 LSB
± 1 LSB
± 1 LSB
± 1 LSB
± 1 LSB
± 1 LSB
± 2 LSB
± 4 LSB
± 4 LSB
± 4 LSB
± 4 LSB
–55°C to +125°C
–40°C to +85°C
0°C to +70°C
–40°C to +85°C
0°C to +70°C
–40°C to +85°C
0°C to +70°C
24-Pin Cerdip
24-Pin Cerdip
24-Pin Plastic DIP
24-Pin Cerdip
24-Pin Plastic DIP
24-Pin Plastic DIP
24-Pin SOL
NOTES
1_{Burn-in is available on commercial and industrial temperature range parts in cerdip, plastic DIP, and TO-can packages.}
2_{For devices processed in total compliance to MIL-STD-883, add/883 after part number. Consult factory for 883 data sheet.}
3_{For availability and burn-in information on SO and PLCC packages, contact your local sales office.}
CAUTION
ESD (electrostatic discharge) sensitive device. Electrostatic charges as high as 4000 V readily
accumulate on the human body and test equipment and can discharge without detection.
Although the DAC8248 features proprietary ESD protection circuitry, permanent damage may
occur on devices subjected to high energy electrostatic discharges. Therefore, proper ESD
precautions are recommended to avoid performance degradation or loss of functionality.
WARNING!
ESD SENSITIVE DEVICE
–4–
REV. B