|
AD8392 Datasheet, PDF (4/16 Pages) Analog Devices – Low Power, High Output Current, Quad Op Amp, Dual-Channel ADSL/ADSL2+ Line Driver | |||
|
◁ |
AD8392
VS = ±5 V or +10 V, RL = 100 â¦, G = +5, PD = (0, 0), T = 25°C, unless otherwise noted.
Table 2.
Parameter
DYNAMIC PERFORMANCE
â3 dB Small Signal Bandwidth
â3 dB Large signal Bandwidth
Peaking
Slew Rate (Rise)
Slew Rate (Fall)
NOISE/DISTORTION PERFORMANCE
Second Harmonic Distortion
Third Harmonic Distortion
Voltage Noise (RTI)
+Input Current Noise
âInput Current Noise
INPUT CHARACTERISTICS
RTI Offset Voltage
+Input Bias Current
âInput Bias Current
Input Resistance
Input Capacitance
Common-Mode Rejection Ratio
OUTPUT CHARACTERISTICS
Differential Output Voltage Swing
Single-Ended Output Voltage Swing
Linear Output Current
POWER SUPPLY
Operating Range (Dual Supply)
Operating Range (Single Supply)
Total Quiescent Current
PD1, PD0 = (0, 0)
PD1, PD0 = (0, 1)
PD1, PD0 = (1, 0)
PD1, PD0 = (1, 1) (Shutdown State)
PD = 0 Threshold
PD = 1 Threshold
+Power Supply Rejection Ratio
âPower Supply Rejection Ratio
Min Typ Max Unit
30
40
MHz
20
25
MHz
0.05
dB
300 350
V/µs
400 450
V/µs
â72
dBc
â82
dBc
4.3
nV/âHz
10
pA/âHz
13
pA/âHz
â5.0 ±3.0 +5.0 mV
5.0
10.0 µA
10.0 15.0 µA
400
kâ¦
2.0
pF
62
66
dB
14.0 16.0 18.0 V
7.0
8.0
9.0
V
400
mA
±5
±12 V
+10
+24 V
5.4
6.0
mA/Amp
3.5
4.0
mA/Amp
2.6
3.0
mA/Amp
0.4
1.0
mA/Amp
0.8
V
1.8
V
72
76
dB
64
68
dB
Test Conditions/Comments
VOUT = 0.1 V p-p, RF = 2 kâ¦
VOUT = 4 V p-p, RF = 2 kâ¦
VOUT = 0.1 V p-p, RF = 2 kâ¦
VOUT = 7 V p-p, RF = 2 kâ¦
VOUT = 7 V p-p, RF = 2 kâ¦
fC = 1 MHz, VOUT = 2 V p-p
fC = 1 MHz, VOUT = 2 V p-p
f = 10 kHz
f = 10 kHz
f = 10 kHz
V+IN â VâIN
(âVOS, DM (RTI))/(âVIN, CM)
âVOUT
âVOUT
RL = 10 â¦, fC = 100 kHz
âVOS, DM (RTI)/âVCC, âVCC = ±1 V
âVOS, DM (RTI)/âVEE, âVEE = ±1 V
Rev. 0 | Page 4 of 16
|
▷ |