AD8187ARUZ-REEL7 Datasheet, PDF (4/20 Pages) Analog Devices – 480 MHz Single-Supply (5 V) Triple 2:1 Multiplexers

AD8186/AD8187
ABSOLUTE MAXIMUM RATINGS^{1, 2, 3, 4}
Supply Voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5.5 V
DV_CC to D_GND . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5.5 V
DV_CC to V_EE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8.0 V
V_CC to D_GND . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8.0 V
IN0A, IN0B, IN1A, IN1B, IN2A, IN2B, V_REF . . . V_EE ≤ V_IN ≤ V_CC
SEL A/B, OE . . . . . . . . . . . . . . . . . . . . . . D_GND ≤ V_IN ≤ DV_CC
Output Short Circuit Operation . . . . . . . . . . . . . . . Indefinite
Storage Temperature Range . . . . . . . . . . . . –65ºC to +150ºC
Lead Temperature Range (Soldering 10 sec) . . . . . . . . . 300ºC
NOTES
1 _{Stresses above those listed under Absolute Maximum Ratings may cause perma-}
nent damage to the device. This is a stress rating only; functional operation of the
device at these or any other conditions above those indicated in the Theory of
Operation section of this specification is not implied. Exposure to absolute
maximum rating conditions for extended periods may affect device reliability.
2 _{Specification is for device in free air (TA = 25ºC).}
3 _{24-lead TSSOP; TJA= 85ºC/W. Maximum internal power dissipation (PD) should be}
derated for ambient temperature (T_A) such that PD < (150ºC T_A)/T_JA.
4 _{TJA of 85ЊC/W is on a 4-layer board (2s 2p).}
MAXIMUM POWER DISSIPATION
The maximum safe junction temperature for plastic encapsulated
devices is determined by the glass transition temperature of the
plastic, approximately 150ºC. Temporarily exceeding this limit
may cause a shift in parametric performance due to a change in
the stresses exerted on the die by the package. Exceeding a
junction temperature of 175ºC for an extended period can result
in device failure.
While the AD8186/AD8187 is internally short circuit protected,
this may not be sufficient to guarantee that the maximum junction
temperature (150ºC) is not exceeded under all conditions. To
ensure proper operation, it is necessary to observe the maximum
power derating curves shown in Figure 2.
2.5
2.0
1.5
1.0
0.5
0
–50 –40 –30 –20 –10 0 10 20 30 40 50 60 70 80 90
AMBIENT TEMPERATURE (؇C)
Figure 2. Maximum Power Dissipation vs. Temperature
PIN CONFIGURATION
IN0A 1
D_GND 2
IN1A 3
24 V_CC
23 OE
22 SEL A/B
V_REF 4
IN2A 5
V_CC 6
V_EE 7
IN2B 8
V_EE 9
IN1B 10
AD8186/
AD8187
TOP VIEW
(Not to Scale)
21 V_CC
20 _{OUT 0}
19 V_EE
18 OUT 1
17 V_CC
16 OUT 2
15 V_EE
V_EE 11
IN0B 12
14 DV_CC
13 V_CC
ORDERING GUIDE
Model
Temperature Range Package Description
Package Option
AD8186ARU
–40ºC to +85ºC
AD8186ARU-REEL –40ºC to +85ºC
AD8186ARU-REEL 7 –40ºC to +85ºC
AD8187ARU
–40ºC to +85ºC
AD8187ARU-REEL –40ºC to +85ºC
AD8187ARU-REEL 7 –40ºC to +85ºC
AD8186-EVAL
AD8187-EVAL
24-Lead Thin Shrink Small Outline Package (TSSOP) RU-24
13" Reel TSSOP
RU-24
7" Reel TSSOP
RU-24
24-Lead Thin Shrink Small Outline Package (TSSOP) RU-24
13" Reel TSSOP
RU-24
7" Reel TSSOP
RU-24
Evaluation Board
Evaluation Board
CAUTION
ESD (electrostatic discharge) sensitive device. Electrostatic charges as high as 4000 V readily
accumulate on the human body and test equipment and can discharge without detection. Although the
AD8186/AD8187 features proprietary ESD protection circuitry, permanent damage may occur on
devices subjected to high energy electrostatic discharges. Therefore, proper ESD precautions are
recommended to avoid performance degradation or loss of functionality.
–4–
REV. A