ADG901-EP Datasheet, PDF (3/11 Pages) Analog Devices – Low power consumption

Enhanced Product
ADG901-EP
SPECIFICATIONS
VDD = 1.65 V to 2.75 V, GND = 0 V, input power = 0 dBm, temperature range = −55°C to +125°C, unless otherwise noted.
Table 1.
Parameter
AC ELECTRICAL CHARACTERISTICS
−3 dB Frequency²
Insertion Loss
Isolation—RF1 to RF2
Return Loss (On Channel)²
Return Loss (Off Channel)²
On Switching Time²
Off Switching Time²
Rise Time²
Fall Time²
Third-Order Intermodulation Intercept
Video Feedthrough³
INPUT POWER
1 dB Input Compression⁴
DC ELECTRICAL CHARACTERISTICS
Input High Voltage
Input Low Voltage
Symbol
S21, S12
S21, S12
S11, S22
S11, S22
tON
tOFF
tRISE
tFALL
IP3
P1dB
VINH
VINH
VINL
VINL
Test Conditions/Comments
DC to 100 MHz; VDD = 2.5 V ± 10%, see
Figure 19
500 MHz; VDD = 2.5 V ± 10%
1000 MHz; VDD = 2.5 V ± 10%
100 MHz
500 MHz
1000 MHz
DC to 100 MHz
500 MHz
1000 MHz
DC to 100 MHz
500 MHz
1000 MHz
50% CTRL to 90% RF, see Figure 16
50% CTRL to 10% RF, see Figure 16
10% to 90% RF, see Figure 17
90% to 10% RF, see Figure 17
900 MHz/901 MHz, 4 dBm, see Figure 21
See Figure 20
1000 MHz; see Figure 22
VDD = 2.25 V to 2.75 V
VDD = 1.65 V to 1.95 V
VDD = 2.25 V to 2.75 V
VDD = 1.65 V to 1.95 V
Min
55
40
31
18
15
28.5
1.7
0.65 VDD
Input Leakage Current
II
0 ≤ VIN ≤ 2.75 V
CAPACITANCE²
RF1/RF2, RF Port On Capacitance
CRF on f = 1 MHz
CTRL Input Capacitance
CCTRL
f = 1 MHz
POWER REQUIREMENTS
VDD
1.65
Quiescent Power Supply Current
IDD
Digital inputs = 0 V or VDD
Typ ¹
4.5
0.4
0.6
0.8
61
45
38
28
25
20
23
21
19
4
6.5
3.1
6.0
36
2.5
17
±0.1
1.2
2.1
0.1
Max Unit
GHz
0.7 dB
1
dB
1.25 dB
dB
dB
dB
dB
dB
dB
dB
dB
dB
6.5 ns
10.5 ns
5.5 ns
9.5 ns
dBm
mV p-p
dBm
V
V
0.7 V
0.35 V
VDD
±1 µA
pF
pF
2.75 V
2.5 µA
1 _{Typical values are at VDD = 2.5 V and 25°C, unless otherwise specified.}
2 _{Guaranteed by design, not subject to production test.}
3 _{Video feedthrough is the dc transience at the output of any port of the switch when the control voltage is switched from high to low or low to high in a 50 Ω test}
setup, measured with 1 ns rise time pulses and 500 MHz bandwidth.
4 _{For less than 100 MHz, refer to the AN-952 Application Note for more information about power handling.}
Rev. A | Page 3 of 11