AD5040_15 Datasheet, PDF (3/24 Pages) Analog Devices – Fully Accurate 14-/16-Bit VOUT nanoDAC SPI Interface 2.7 V to 5.5 V, in an SOT-23

AD5040/AD5060
SPECIFICATIONS
VDD = 5.5 V, VREF = 4.096 V @ RL = unloaded, CL = unloaded; TMIN to TMAX, unless otherwise noted.
Table 2.
Parameter
STATIC PERFORMANCE
Resolution
Relative Accuracy (INL)²
Total Unadjusted Error (TUE)²
Differential Nonlinearity (DNL)²
A, B, and Y Grades¹
Min Typ
Max
16
14
±0.5
±2
±0.5
±1
±0.5
±1.5
±0.1
±2.0
±0.1
±2.0
±0.5
±1
±0.5
±1
Gain Error
Gain Error Temperature Coefficient
Offset Error
Offset Error Temperature Coefficient
Full-Scale Error
±0.01
±0.01
1
±0.02
±0.02
0.5
±0.05
±0.02
±0.03
±1.5
±2.0
±2.0
±0.05
±2.0
OUTPUT CHARACTERISTICS³
Output Voltage Range
Output Voltage Settling Time
0
VREF
4
Output Noise Spectral Density
64
Output Voltage Noise
6
Digital-to-Analog Glitch Impulse
2
Digital Feedthrough
DC Output Impedance (Normal)
DC Output Impedance (Power-Down)
(Output Connected to 1 kΩ Network)⁴
(Output Connected to 100 kΩ
Network)
Capacitive Load Stability
Slew Rate
0. 003
0. 015
1
100
1
1. 2
Short-Circuit Current
60
45
DAC Power-Up Time
4.5
DC Power Supply Rejection Ratio
−92.11
Unit
Test Conditions/Comments
Bits
Bits
LSB
LSB
mV
LSB
% of FSR
ppm of FSR/°C
mV
μV/°C
mV
AD5060
AD5040
−40°C to +85°C, AD5040/AD5060 A grade
−40°C to +85°C, AD5040/AD5060 B grade
−40°C to +125°C, AD5060 Y grade
−40°C to +85°C, AD5040/AD5060
−40°C to +125°C, AD5060 Y grade
Guaranteed monotonic,
−40°C to +85°C, AD5040/AD5060
Guaranteed monotonic,
−40°C to +125°C, Y grade
TA = −40°C to +85°C, AD5040/AD5060
TA = −40°C to +125°C AD5060 Y grade
TA = −40°C to + 85°C, AD5040/AD5060
TA = −40°C to + 125°C, AD5060 Y grade
All 1s loaded to DAC register,
AD5040 AD5060; TA = −40°C to +85°C
All 1s loaded to DAC register,
TA = −40°C to +125°C, AD5060 Y grade
V
μs
nV/√Hz
μV p-p
nV-s
nV-s
Ω
¼ scale to ¾ scale code transition to
±1 LSB, RL = 5 kΩ
DAC code = midscale, 1 kHz
DAC code = midscale , 0.1 Hz to 10 Hz
bandwidth
1 LSB change around code 57386,
RL = 5 kΩ, CL = 200 pF
DAC code = full scale
Output impedance tolerance ±10%
kΩ
Output impedance tolerance ±400 Ω
kΩ
Output impedance tolerance ±20 kΩ
nF
Loads used RL = 5 kΩ, RL = 100 kΩ, RL = ∞
V/μs
¼ scale to ¾ scale code transition to
±1 LSB, RL = 5 kΩ, CL = 200 pF
ma
DAC code = full scale, output shorted to
GND, TA = 25°C
DAC code = zero scale, output shorted to
VDD, TA = 25°C
μs
Time to exit power-down mode to normal
mode of AD5060, 24^th clock edge to 90%
of DAC final value, output unloaded
db
VDD ± 10%, DAC code = full scale
Rev. A | Page 3 of 24