OP290 Datasheet, PDF (2/12 Pages) Analog Devices – Precision, Low Power, Micropower Dual Operational Amplifier

OP290–SPECIFICATIONS
ELECTRICAL CHARACTERISTICS ^{(@ V}S ^{= ؎1.5 V to ؎15 V, T}A ^{= 25؇C, unless otherwise noted.)}
OP290E
OP290F
OP290G
Parameter
Symbol Conditions
Min Typ Max Min Typ Max Min Typ Max Unit
INPUT OFFSET VOLTAGE
V_OS
INPUT OFFSET CURRENT
I_OS
INPUT BIAS CURRENT
I_B
LARGE-SIGNAL
A_VO
VOLTAGE GAIN
INPUT VOLTAGE RANGE¹
IVR
OUTPUT VOLTAGE SWING
V_O
COMMON-MODE
REJECTION
V_OH
V_OL
CMR
POWER SUPPLY
PSRR
REJECTION RATIO
SUPPLY CURRENT I_SY
(All Amplifiers)
CAPACITIVE LOAD
STABILITY
INPUT NOISE VOLTAGE¹
e_np-p
INPUT RESISTANCE
DIFFERENTIAL-MODER_IN
INPUT RESISTANCE R_INCM
COMMON-MODE
50 200
75 300
125 500 µV
V_CM = 0 V
0.1 3
0.1 5
0.1 5 nA
V_CM = 0 V
V_S = ±15 V, V_O = ±10 V
R_L = 100 kΩ
700
R_L = 10 kΩ
350
R_L = 2 kΩ
125
V+ = 5V, V– = 0 V,
1 V < V_O < 4 V
R_L = 100 kΩ
200
R_L = 10 kΩ
100
4.0 15
1200
500
600
250
250
100
400
125
180
75
4.0 20
4.0 25 nA
1000
500
200
400 600
200 400
100 200
V/mV
300
100 250
140
70 140
V+ = 5 V, V– = 0 V 0/4
V_S = ± 5 V¹
–15/13.5
0/4
–15/13.5
0/4
V
–15/13.5
V_S = ± 5 V
R_L = 10 kΩ
R_L = 2 kΩ
V+ = 5 V, V– = 0 V
V+ = 5 V, V– = 0 V
R_L = 10kn
± 13.5± 14.2
± 10.5± 11.5
40
4.2
10
50
V+ = 5 V, V– = 0 V
ttS
0 V < V_CM < 4 V
V_S = ± 15 V,
100 120
–15 V < V_CM < 13.5 V
10 5.6
± 13.5± 14.2
± 10.5± 11.5
4.0 4.2
10
50
80
100
90
120
±13.5 ± 14.2 V
±10.5 ± 11.5
4.0 4.2
10 50
80 100
90 120
10 5.6
3.2 10
V
µV
dB
µV/V
V_S = ± 1.5 V
V_S = ± 15 V
A_V = +1
No Oscillations
19 30
25 40
650
19 30
25 40
650
19 30 µA
25 40
650
PF
f_O = 0.1 Hz to 10 Hz
3
V_S = ± 15 V
V_S = ±15 V
30
V_S = ± 15 V
20
3
3
µV_p-p
30
30
MΩ
20
20
GΩ
SLEW RATE
GAIN BANDWIDTH
PRODUCT
CHANNEL
SEPARATION²
SR
GBWP
CS
A_V = +1
V_S = ± 15 V
Vs = +15 V
V_S = ± 15 V
f_O = 10 Hz
V_O = 20 Vp-p
V_S = ± 15 V²
5
12
20
120 150
5
12
20
120 150
5
12
20
120 150
V/ms
kHz
dB
NOTES
1_{Guaranteed by CMR test.}
2_{Guaranteed but not 100% tested.}
Specifications subject to change without notice.
–2–
REV. A