OP-150_15 Datasheet, PDF (2/5 Pages) Analog Devices – CMOS Single-Supply Rail-to-Rail Input/Output Operational Amplifier

OP150/OP250/OP450–SPECIFICATIONS
ELECTRICAL CHARACTERISTICS ^{(@ V}S ^{= +3.0 V, V}CM ^{= 0.05 V, V}O ^{= 1.4 V, T}A ^{= +25؇C, unless otherwise noted)}
Parameter
Symbol
Conditions
Min
Typ
Max Units
INPUT CHARACTERISTICS
Offset Voltage OP150
V_OS
–40°C ≤ T_A ≤ +125°C
5
mV
mV
Offset Voltage OP250/OP450
V_OS
–40°C ≤ T_A ≤ +125°C
5
mV
mV
Input Bias Current
I_B
–40°C ≤ T_A ≤ +125°C
10
60 pA
pA
Input Offset Current
I_OS
–40°C ≤ T_A ≤ +125°C
25
pA
pA
Input Voltage Range
0
3
V
OBSOLETE ^{Common-ModeRejectionRatio CMRR}
V_CM = 0 V to 3 V
60
–40°C ≤ T_A ≤ +125°C
Large Signal Voltage Gain
A_VO
R_L = 10 kΩ, V_O = 0.3 V to 2.7 V
40
–40°C ≤ T_A ≤ +125°C
Large Signal Voltage Gain
A_VO
R_L = 2 kΩ, V_O = 0.3 V to 2.7 V
16
Large Signal Voltage Gain
A_VO
R_L = 1 kΩ, V_O = 0.3 V to 2.7 V
10
Offset Voltage Drift
∆V_OS/∆T
Bias Current Drift
∆I_B/∆T
Offset Current Drift
∆I_OS/∆T
dB
dB
V/mV
V/mV
V/mV
V/mV
µV/°C
pA/°C
pA/°C
OUTPUT CHARACTERISTICS
Output Voltage High
V_OH
Output Voltage Low
V_OL
I_L = 100 µA
–40°C to +125°C
I_L = 10 mA
–40°C to +125°C
I_L = 100 µA
–40°C to +125°C
I_L = 10 mA
2.95
2.99
V
V
2.95
V
V
2
10 mV
mV
30
55 mV
–40°C to +125°C
mV
Output Current
I_OUT
–40°C to +125°C
± 250
mA
mA
Open Loop Impedance
Z_OUT
f = 1 MHz, A_V = 1
Ω
POWER SUPPLY
Power Supply Rejection Ratio
Supply Current/Amplifier
PSRR
I_SY
V_S = 2.7 V to 6 V
–40°C ≤ T_A ≤ +125°C
V_O = 0 V
–40°C ≤ T_A ≤ +125°C
70
dB
68
dB
500
600 µA
650
µA
DYNAMIC PERFORMANCE
Slew Rate
Settling Time
Gain Bandwidth Product
Phase Margin
Channel Separation
SR
t_S
GBP
Øo
CS
R_L =10 kΩ
To 0.01%
f = 1 kHz, R_L =10 kΩ
2.7
V/µs
µs
2
MHz
75
Degrees
dB
NOISE PERFORMANCE
Voltage Noise
Voltage Noise Density
Current Noise Density
e_n p-p
e_n
i_n
0.1 Hz to 10 Hz
f = 1 kHz
µV p-p
55
nV/√Hz
pA/√Hz
Specifications subject to change without notice.
This information applies to a product under development. Its characteristics and specifications are subject to change without notice.
Analog Devices assumes no obligation regarding future manufacture unless otherwise agreed to in writing.
PRELIMINARY TECHNICAL DATA
–2–
REV. 0