AD9901_15 Datasheet, PDF (2/8 Pages) Analog Devices – Ultrahigh Speed Phase/Frequency Discriminator

AD9901–SPECIFICATIONS
ABSOLUTE MAXIMUM RATINGS¹
Positive Supply Voltage (+V_S for TTL Operation) . . . . . +7 V
Negative Supply Voltage (–V_S for ECL Operation) . . . . . –7 V
Input Voltage Range (TTL Operation) . . . . . . . 0 V to +5.5 V
Differential Input Voltage (ECL Operation) . . . . . . . . . . 4.0 V
I_SET Current . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 mA
Output Current . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30 mA
Operating Temperature Range
AD9901KQ/KP . . . . . . . . . . . . . . . . . . . . . . . 0°C to +70°C
Storage Temperature Range . . . . . . . . . . . . –65°C to +150°C
Junction Temperature²
Plastic . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .+150°C
Ceramic . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .+175°C
Lead Soldering Temperature (10 sec) . . . . . . . . . . . . .+300°C
ELECTRICAL CHARACTERISTICS (؎VS = +5.0 V [for TTL] or –5.2 V [for ECL], unless otherwise noted)
Temp
Test
Level
Commercial Temperature
0؇C to +70؇C
AD9901KQ/KP
Min
Typ
Max
Units
INPUT CHARACTERISTICS
TTL Input Logic “1” Voltage
Full
VI
2.0
TTL Input Logic “0” Voltage
TTL Input Logic “1” Current³
TTL Input Logic “0” Current³
Full
VI
Full
VI
Full
VI
ECL Differential Switching Voltage
Full
VI
300
ECL Input Current
Full
VI
V
0.8
V
0.6
mA
1.6
mA
mV
20
µA
OUTPUT CHARACTERISTICS
Peak-to-Peak Output Voltage Swing⁴
Full
VI
1.6
1.8
2.0
V
TTL Output Compliance Range
Full
V
3–7
V
ECL Output Compliance Range
Full
V
±2
V
I_OUT Range
Internal Reference Voltage
Full
V
0.9–11
mA
Full
VI
0.42
0.47
0.52
V
AC CHARACTERISTICS
Linear Phase Detection Range⁴
40 kHz
30 MHz
70 MHz
Functionality @ 70 MHz
+25°C
V
+25°C
V
+25°C
V
+25°C
I
360
320
270
Pass/Fail
Degrees
Degrees
Degrees
POWER SUPPLY CHARACTERISTICS
TTL Supply Current (+5.0 V)^{5, 6}
+25°C
I
Full
I
ECL Supply Current (–5.2 V)^{5, 6}
+25°C
I
Full
I
Nominal Power Dissipation
+25°C
V
43.5
54.0
mA
43.5
54.0
mA
42.5
52.5
mA
42.5
52.5
mA
218
mW
NOTES
1_{Absolute maximum ratings are limiting values, to be applied individually, and beyond which the service ability of the circuit may be impaired. Functional operability}
is not necessarily implied. Exposure to absolute maximum rating conditions for an extended period of time may affect device reliability.
2_{Maximum junction temperature should not exceed +175 °C for ceramic packages, +150°C for plastic packages. Junction temperature can be calculated by:}
t_J = PD (θ_JA) +t_A = PD (θ_JC) +t_C
where:
PD = power dissipation
θ_JA = thermal impedance from junction to air (°C/W)
θ_JC = thermal impedance from junction to case ( °C/W)
t_A = ambient temperature (°C)
t_C = case temperature (°C)
typical thermal impedances:
AD9901 Ceramic DIP = θ_JA = 74°C/W; θ_JC = 21°C/W
AD9901 LCC = θ_JA = 80°C/W; θ_JC = 19°C/W
AD9901 PLCC = θ_JA = 88.2°C/W; θ_JC = 45.2°C/W
3_{VL = +0.4 V; VH = +2.4 V.}
4_{RSET = 47.5 Ω; RL = 182 Ω.}
5_{lncludes load current of 10 mA (load resistors = 182 Ω).}
6_{Supply should remain stable within ± 5% for normal operation.}
Specifications subject to change without notice.
–2–
REV. B