AD8061 Datasheet, PDF (2/16 Pages) Analog Devices – Low-Cost, 300 MHz Rail-to-Rail Amplifiers

AD8061/AD8062/AD8063–SPECIFICATIONS (TA = 25؇C, VS = 5 V, RL = 1 k⍀, VO = 1 V,
unless otherwise noted)
Parameter
Conditions
Min Typ
Max
Unit
DYNAMIC PERFORMANCE
–3 dB Small Signal Bandwidth
–3 dB Large Signal Bandwidth
Bandwidth for 0.1 dB Flatness
Slew Rate
Settling Time to 0.1%
NOISE/DISTORTION PERFORMANCE
Total Harmonic Distortion
Crosstalk, Output to Output
Input Voltage Noise
Input Current Noise
Differential Gain Error (NTSC)
Differential Phase Error (NTSC)
Third Order Intercept
SFDR
G = 1, V_O = 0.2 V p-p
G = –1, +2, V_O = 0.2 V p-p
G = 1, V_O = 1 V p-p
G = 1, V_O = 0.2 V p-p
G = 1, V_O = 2 V Step, R_L = 2 kΩ
G = 2, V_O = 2 V Step, R_L = 2 kΩ
G = 2, V_O = 2 V Step
150 320
60
115
280
30
500 650
300 500
35
f_C = 5 MHz, V_O = 2 V p-p, R_L = 1 kΩ
–77
f_C = 20 MHz, V_O = 2 V p-p, R_L = 1 kΩ
–50
f = 5 MHz, G = 2, AD8062
–90
f = 100 kHz
8.5
f = 100 kHz
1.2
G = 2, R_L = 150 Ω
0.01
G = 2, R_L = 150 Ω
0.04
f = 10 MHz
28
f = 5 MHz
62
MHz
MHz
MHz
MHz
V/µs
V/µs
ns
dBc
dBc
dBc
nV/√Hz
pA/√Hz
%
Degree
dBc
dB
DC PERFORMANCE
Input Offset Voltage
Input Offset Voltage Drift
Input Bias Current
Input Offset Current
Open-Loop Gain
INPUT CHARACTERISTICS
Input Resistance
Input Capacitance
Input Common-Mode Voltage Range
Common-Mode Rejection Ratio
OUTPUT CHARACTERISTICS
Output Voltage Swing—Load Resistance
Is Terminated at Midsupply
Output Current
Capacitive Load Drive, V_OUT = 0.8 V
POWER-DOWN DISABLE
Turn-On Time
Turn-Off Time
DISABLE Voltage—Off
DISABLE Voltage—On
T_MIN to T_MAX
T_MIN to T_MAX
V_O = 0.5 V to 4.5 V, R_L = 150 Ω
V_O = 0.5 V to 4.5 V, R_L = 2 kΩ
V_CM = –0.2 V to +3.2 V
R_L = 150 Ω
R_L = 2 kΩ
V_O = 0.5 V to 4.5 V
30% Overshoot: G = 1, R_S = 0 Ω
G = 2, R_S = 4.7 Ω
1
6
2
6
3.5
3.5
9
4
9
0.3
4.5
68
70
74
90
13
1
–0.2 to +3.2
62
80
0.3
0.1 to 4.5
4.75
0.25 0.1 to 4.9
4.85
25
50
25
300
40
300
2.8
3.2
mV
mV
µV/°C
µA
µA
±µA
dB
dB
MΩ
pF
V
dB
V
V
mA
pF
pF
ns
ns
V
V
POWER SUPPLY
Operating Range
Quiescent Current per Amplifier
Supply Current when Disabled
(AD8063 Only)
Power Supply Rejection Ratio
∆V_S = 2.7 V to 5 V
2.7
5
6.8
0.4
72
80
8
V
9.5
mA
mA
dB
Specifications subject to change without notice.
–2–
REV. C