AD8015_15 Datasheet, PDF (2/8 Pages) Analog Devices – Wideband/Differential Output Transimpedance Amplifier

AD8015–SPECIFICATIONS ^{(SO Package @ T}A ^{= +25؇C and V}S ^{= +5 V, unless otherwise noted)}
Parameter
Conditions
AD8015AR
Min
Typ
Max
Units
DYNAMIC PERFORMANCE
Bandwidth
Pulse Width Modulation
Rise and Fall Time
Settling Time¹
3 dB
10 µA to 200 µA Peak
10% to 90%
to 3%, 0.5 V Diff Output Step
180
240
500
1.5
3
MHz
ps
ns
ns
INPUT
Linear Input Current Range
Max Input Current Range
Optical Sensitivity
Input Stray Capacitance
Input Bias Voltage
NOISE
Input Current Noise
Total Input RMS Noise
± 2.5%, Nonlinearity
Saturation
155 Mbps, Avg Power
Die, by Design
SOIC, by Design
+V_S to I_IN and V_BYP
Die, Single Ended at P_OUT,
or Differential (P_OUT–N_OUT),
C_STRAY = 0.3 pF
f = 100 MHz
DC to 100 MHz
± 25
± 30
± 200
± 350
–36
0.2
0.4
1.6
1.8
2.0
µA
µA
dBm
pF
pF
V
3.0
pA/√Hz
26.5
nA
TRANSFER CHARACTERISTICS
Transresistance
Power Supply
Rejection Ratio
Single Ended
Differential
Single Ended
Differential
8
10
12
kΩ
16
20
24
kΩ
37.0
dB
40
dB
OUTPUT
Differential Offset
6
20
mV
Output Common-Mode Voltage
From Positive Supply
–1.5
–1.3
–1.1
V
Voltage Swing (Differential)
Output Impedance
Positive Input Current, R_L = ∞
Positive Input Current, R_L = 50 Ω
40
1.0
V p-p
600
mV p-p
50
60
Ω
POWER SUPPLY
Operating Range
Current
T_MIN to T_MAX
Single Supply
Dual Supply
+4.5
+5
± 2.25
25
+11
V
± 5.5
V
26
mA
NOTES
1_{Settling Time is defined as the time elapsed from the application of a perfect step input to the time when the output has entered and remained within a specified error}
band symmetrical about the final value. This parameter includes propagation delay, slew time, overload recovery, and linear settling times.
Specifications subject to change without notice.
ABSOLUTE MAXIMUM RATINGS¹
Supply Voltage (+V_S to –V_S). . . . . . . . . . . . . . . . . . . . . . . 12 V
Internal Power Dissipation²
Small Outline . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0.9 Watts
Output Short Circuit Duration . . . . . . . . . . . . . . . Indefinite
Maximum Input Current . . . . . . . . . . . . . . . . . . . . . . . . 10 mA
Storage Temperature Range . . . . . . . . . . . . –65°C to +125°C
Operating Temperature Range (T_MIN to T_MAX)
AD8015ACHIP/AR . . . . . . . . . . . . . . . . . . –40°C to +85°C
Maximum Junction Temperature . . . . . . . . . . . . . . . . . +165°C
Lead Temperature Range (Soldering 10 sec) . . . . . . . . +300°C
NOTES
1_{Stresses above those listed under “Absolute Maximum Ratings” may cause}
permanent damage to the device. This is a stress rating only and functional
operation of the device at these or any other conditions above those indicated in the
operational section of this specification is not implied. Exposure to absolute
maximum rating conditions for extended periods may affect device reliability.
2_{Specification is for device in free air: 8-pin SOIC package: θJA = 155°C/W.}
ORDERING GUIDE
Model
Temperature Package
Range
Description
Package
Option
AD8015AR
–40°C to +85°C 8-Pin Plastic SOIC SO-8
AD8015ACHIPS –40°C to +85°C Die Form
CAUTION
ESD (electrostatic discharge) sensitive device. Electrostatic charges as high as 4000 V readily
accumulate on the human body and test equipment and can discharge without detection.
Although the AD8015 features proprietary ESD protection circuitry, permanent damage may
occur on devices subjected to high energy electrostatic discharges. Therefore, proper ESD
precautions are recommended to avoid performance degradation or loss of functionality.
WARNING!
ESD SENSITIVE DEVICE
–2–
REV. A