OP200_04 Datasheet, PDF (11/12 Pages) Analog Devices – Dual Low Offset, Low Power Operational Amplifier

OUTLINE DIMENSIONS
OP200
8-Lead Ceramic Dual In-Line Package [CERDIP]
(Q-8)
Z-Suffix
Dimensions shown in inches and (millimeters)
0.005 (0.13) 0.055 (1.40)
MIN
MAX
8
PIN 1
1
5
0.310 (7.87)
0.220 (5.59)
4
0.100 (2.54) BSC
0.405 (10.29) MAX
0.200 (5.08)
MAX
0.060 (1.52)
0.015 (0.38)
0.320 (8.13)
0.290 (7.37)
0.200 (5.08)
0.125 (3.18)
0.023 (0.58)
0.014 (0.36)
0.150 (3.81)
MIN
0.070 (1.78)
SEATING
PLANE
0.030 (0.76)
15
0
0.015 (0.38)
0.008 (0.20)
CONTROLLING DIMENSIONS ARE IN INCHES; MILLIMETERS DIMENSIONS
(IN PARENTHESES) ARE ROUNDED-OFF INCH EQUIVALENTS FOR
REFERENCE ONLY AND ARE NOT APPROPRIATE FOR USE IN DESIGN
8-Lead Plastic Dual In-Line Package [PDIP]
(N-8)
P-Suffix
Dimensions shown in inches and (millimeters)
0.375 (9.53)
0.365 (9.27)
0.355 (9.02)
8
5 _{0.295 (7.49)}
0.285 (7.24)
1
4 0.275 (6.98)
0.100 (2.54)
BSC
0.180
(4.57)
MAX
0.150 (3.81)
0.130 (3.30)
0.110 (2.79)
0.022 (0.56)
0.018 (0.46)
0.014 (0.36)
0.015
(0.38)
MIN
SEATING
PLANE
0.060 (1.52)
0.050 (1.27)
0.045 (1.14)
0.325 (8.26)
0.310 (7.87)
0.300 (7.62)
0.150 (3.81)
0.135 (3.43)
0.120 (3.05)
0.015 (0.38)
0.010 (0.25)
0.008 (0.20)
COMPLIANT TO JEDEC STANDARDS MO-095AA
CONTROLLING DIMENSIONS ARE IN INCHES; MILLIMETER DIMENSIONS
(IN PARENTHESES) ARE ROUNDED-OFF INCH EQUIVALENTS FOR
REFERENCE ONLY AND ARE NOT APPROPRIATE FOR USE IN DESIGN
16-Lead Standard Small Outline Package [SOIC]
Wide Body
(RW-16)
S-Suffix
Dimensions shown in millimeters and (inches)
10.50 (0.4134)
10.10 (0.3976)
16
9
7.60 (0.2992)
7.40 (0.2913)
10.65 (0.4193)
1
8
10.00 (0.3937)
0.30 (0.0118)
0.10 (0.0039)
1.27 (0.0500)
BSC
COPLANARITY
0.10
0.51 (0.0201)
0.31 (0.0122)
2.65 (0.1043)
2.35 (0.0925)
0.75 (0.0295)
0.25 (0.0098)^{؋ 45؇}
SEATING
PLANE
8؇
0.33 (0.0130) ^0؇
0.20 (0.0079)
1.27 (0.0500)
0.40 (0.0157)
COMPLIANT TO JEDEC STANDARDS MS-013AA
CONTROLLING DIMENSIONS ARE IN MILLIMETERS; INCH DIMENSIONS
(IN PARENTHESES) ARE ROUNDED-OFF MILLIMETER EQUIVALENTS FOR
REFERENCE ONLY AND ARE NOT APPROPRIATE FOR USE IN DESIGN
REV. B
–11–