AD8565_15 Datasheet, PDF (1/16 Pages) Analog Devices – 16 V Rail-to-Rail Operational Amplifiers

FEATURES
Single-supply operation: 4.5 V to 16 V
Input capability beyond the rails
Rail-to-rail output swing
Continuous output current: 35 mA
Peak output current: 250 mA
Offset voltage: 10 mV
Slew rate: 6 V/μs
Unity gain stable with large capacitive loads
Supply current: 700 μA per amplifier
Qualified for automotive applications
APPLICATIONS
LCD reference drivers
Portable electronics
Communications equipment
Automotive infotainment systems
GENERAL DESCRIPTION
The AD8565/AD8566/AD8567 are low cost, single-supply, rail-
to-rail input and output operational amplifiers optimized for
LCD monitor applications. They are built on an advanced high
voltage CBCMOS process. The AD8565 contains a single
amplifier, the AD8566 has two amplifiers, and the AD8567 has
four amplifiers.
These LCD op amps have high slew rates, 35 mA continuous
output drive, 250 mA peak output drive, and a high capacitive
load drive capability. They have a wide supply range and offset
voltages below 10 mV. The AD8565/AD8566/AD8567 are ideal
for LCD grayscale reference buffer and VCOM applications.
The AD8565/AD8566/AD8567 are specified over the −40°C to
+85°C temperature range. The AD8565 single is available in a 5-
lead SC70 package. The AD8566 dual is available in an 8-lead
MSOP package. The AD8567 quad is available in a 14-lead
TSSOP package and a 16-lead LFCSP package.
The AD8566WARMZ is the automotive grade version.
16 V Rail-to-Rail
Operational Amplifiers
AD8565/AD8566/AD8567
PIN CONFIGURATIONS
AD8565
OUT 1
5 V–
V+ 2
+IN 3
4 –IN
TOP VIEW
(Not to Scale)
Figure 1. 5-Lead SC70 Pin Configuration
OUT A 1
AD8566 _{8 V+}
–IN A 2
7 OUT B
+IN A 3
6 –IN B
V– 4
TOP VIEW
5 +IN B
(Not to Scale)
Figure 2. 8-Lead MSOP Pin Configuration
OUT A 1
14 OUT D
–IN A 2
13 –IN D
+IN A 3
V+ 4
AD8567
TOP VIEW
(Not to Scale)
12 +IN D
11 V–
+IN B 5
10 +IN C
–IN B 6
9 –IN C
OUT B 7
8 OUT C
Figure 3. 14-Lead TSSOP Pin Configuration
16 15 14 13
–IN A ¹
12 –IN D
+IN A 2 ^AD8567 11 +IN D
TOP VIEW
V+ 3 _{(Not to Scale)} 10 V–
+IN B 4
9 +IN C
5678
NOTES
1. THE EXPOSED PAD MUST BE
CONNECTED TO PIN 3, THAT IS, V+.
2. NC = NO CONNECT.
Figure 4. 16-Lead LFCSP Pin Configuration
Rev. G
Information furnished by Analog Devices is believed to be accurate and reliable. However, no
responsibility is assumed by Analog Devices for its use, nor for any infringements of patents or other
rights of third parties that may result from its use. Specifications subject to change without notice. No
license is granted by implication or otherwise under any patent or patent rights of Analog Devices.
Trademarks and registered trademarks are the property of their respective owners.
One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106, U.S.A.
Tel: [phone]
www.analog.com
Fax: [phone] ©2001–2010 Analog Devices, Inc. All rights reserved.