AD8352 Datasheet, PDF (1/20 Pages) Analog Devices – 2 GHz Ultralow Distortion Differential RF/IF Amplifier

FEATURES
−3 dB bandwidth of 2.2 GHz (AV = 10 dB)
Single resistor gain adjust 3 dB ≤ AV ≤ 21 dB
Single resistor and capacitor distortion adjust
Input resistance 3 kΩ, independent of gain (AV)
Differential or single-ended input to differential output
Low noise input stage 2.7 nV/√Hz RTI @ AV = 10 dB
Low broadband distortion
10 MHz: −86 dBc HD2, −82 dBc HD3
70 MHz: −84 dBc HD2, −82 dBc HD3
190 MHz: −81 dBc HD2, −87 dBc HD3
OIP3 of 41 dBm @ 150 MHz
Slew rate 8 V/ns
Fast settling and overdrive recovery of 2 ns
Single-supply operation: 3 V to 5.0 V
Low power dissipation: 37 mA @ 5 V
Power down capability: 5 mA @ 5 V
Fabricated using the high speed XFCB3 SiGe process
APPLICATIONS
Differential ADC drivers
Single-ended to differential conversion
RF/IF gain blocks
SAW filter interfacing
GENERAL DESCRIPTION
The AD8352 is a high performance differential amplifier
optimized for RF and IF applications. It achieves better than
80 dB SFDR performance at frequencies up to 200 MHz, and
65 dB beyond 500 MHz, making it an ideal driver for high
speed 12- to 16-bit analog-to-digital converters (ADCs).
Unlike other wideband differential amplifiers, the AD8352 has
buffers that isolate the Gain Setting Resistor RG from the signal
inputs. As a result, the AD8352 maintains a constant 3 kΩ input
resistance for gains of 3 dB to 24 dB, easing matching and input
drive requirements. The AD8352 has a nominal 100 Ω differential
output resistance.
2 GHz Ultralow Distortion
Differential RF/IF Amplifier
AD8352
FUNCTIONAL BLOCK DIAGRAM
ENB
RGP
BIAS CELL
VCM
VCC
C_D
R_G
RDP
VIP
R_D
VIN
RDN
RGN
–60
+
–
Figure 1.
VOP
VON
GND
AD8352
44
–65
42
–70
40
–75
38
–80
36
–85
34
–90
32
–95
30
–100
28
20 40 60 80 100 120 140 160 180 200 220
FREQUENCY (MHz)
Figure 2. IP3 and Third Harmonic Distortion vs. Frequency,
Measured Differentially
The device is optimized for wide band, low distortion
performance at frequencies beyond 500 MHz. These attributes,
together with its wide gain adjust capability, make this device
the amplifier of choice for general-purpose IF and broadband
applications where low distortion, noise, and power are critical.
In particular, it is ideally suited for driving not only ADCs, but
also mixers, pin diode attenuators, SAW filters, and multielement
discrete devices. The device comes in a compact 3 mm × 3 mm,
16-lead LFCSP package and operates over a temperature range of
−40°C to +85°C.
Rev. 0
Information furnished by Analog Devices is believed to be accurate and reliable. However, no
responsibility is assumed by Analog Devices for its use, nor for any infringements of patents or other
rights of third parties that may result from its use. Specifications subject to change without notice. No
license is granted by implication or otherwise under any patent or patent rights of Analog Devices.
Trademarks and registered trademarks are the property of their respective owners.
One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106, U.S.A.
Tel: [phone]
www.analog.com
Fax: [phone]
©2006 Analog Devices, Inc. All rights reserved.