AD7923_15 Datasheet, PDF (1/24 Pages) Analog Devices – 4-Channel, 200 kSPS 12-Bit ADC with Sequencer in 16-Lead TSSOP

Data Sheet
4-Channel, 200 kSPS 12-Bit ADC
with Sequencer in 16-Lead TSSOP
AD7923
FEATURES
Fast throughput rate: 200 kSPS
Specified for AVDD of 2.7 V to 5.25 V
Low power
3.6 mW max at 200 kSPS with 3 V supply
7.5 mW max at 200 kSPS with 5 V supply
4 (single-ended) inputs with sequencer
Wide input bandwidth
70 dB Min SNR at 50 kHz input frequency
Flexible power/serial clock speed management
No pipeline delays
High speed serial interface SPI^®-/QSPI^TM-/
MICROWIRE^TM-/DSP-compatible
Shutdown mode: 0.5 μA max
16-lead TSSOP package
Qualified for automotive applications
GENERAL DESCRIPTION
The AD7923 is a 12-bit, high speed, low power, 4-channel, suc-
cessive approximation (SAR) ADC. It operates from a single
2.7 V to 5.25 V power supply and features throughput rates up to
200 kSPS. It contains a low noise, wide bandwidth track-and-hold
amplifier that can handle input frequencies in excess of 8 MHz.
The conversion process and data acquisition are controlled by
CS and the serial clock, allowing the device to easily interface
with microprocessors or DSPs. The input signal is sampled on
the falling edge of CS; the conversion is also initiated at this
point.
The AD7923 uses advanced design techniques to achieve very
low power dissipation at maximum throughput rates. At
maximum throughput rates, it consumes 1.2 mA maximum
with 3 V supplies and 1.5 mA maximum with 5 V supplies.
Through the configuration of the control register, the analog
input range can be selected as 0 V to REFIN or 0 V to 2 × REFIN,
with either straight binary or twos complement output coding.
The AD7923 features four single-ended analog inputs with a
channel sequencer to allow a preprogrammed selection of
channels to be converted sequentially.
The conversion time for the AD7923 is determined by the serial
clock, SCLK, frequency, since this is used as the master clock to
control the conversion. The conversion time can be as short as
800 ns with a 20 MHz SCLK.
FUNCTIONAL BLOCK DIAGRAM
AV_DD
REF_IN
V_IN0
•
•
•
•
•
•
•
•
•
•
•
•
•
V_IN3
T/H
I/P
MUX
SEQUENCER
12-BIT
SUCCESSIVE
APPROXIMATION
ADC
CONTROL LOGIC
AD7923
GND
SCLK
DOUT
DIN
CS
V_DRIVE
Figure 1.
PRODUCT HIGHLIGHTS
1. High Throughput with Low Power Consumption.
The AD7923 offers up to 200 kSPS throughput rates. At the
maximum throughput rate with 3 V supplies, the AD7923
dissipates just 3.6 mW of power.
2. Four Single-Ended Inputs with a Channel Sequencer.
3. Single-Supply Operation with VDRIVE Function.
The VDRIVE function allows the serial interface to connect
directly to either 3 V or 5 V processor systems independent
of AVDD.
4. Flexible Power/Serial Clock Speed Management.
The conversion rate is determined by the serial clock,
allowing the conversion time to be reduced through the
serial clock speed increase. The part also features various
shutdown modes to maximize power efficiency at lower
throughput rates. Current consumption is 0.5 μA
maximum when in full shutdown.
5. No Pipeline Delay.
The part features a SAR ADC with accurate control of the
sampling instant via a CS input and once off conversion
control.
Rev. D
Document Feedback
Information furnished by Analog Devices is believed to be accurate and reliable. However, no
responsibility is assumed by Analog Devices for its use, nor for any infringements of patents or other
rights of third parties that may result from its use. Specifications subject to change without notice. No
license is granted by implication or otherwise under any patent or patent rights of Analog Devices.
Trademarks and registered trademarks are the property of their respective owners.
One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106, U.S.A.
Tel: [phone] ©2002–2013 Analog Devices, Inc. All rights reserved.
Technical Support
www.analog.com