AD7751_15 Datasheet, PDF (1/14 Pages) Analog Devices – Energy Metering IC with On-Chip Fault Detection

a
FEATURES
High Accuracy, Supports 50 Hz/60 Hz IEC 521/1036
Less than 0.1% Error Over a Dynamic Range of 500 to 1
The AD7751 Supplies Average Real Power On the
Frequency Outputs F1 and F2
The High Frequency Output CF Is Intended for Calibra-
tion and Supplies Instantaneous Real Power Data
Continuous Monitoring of the Phase and Neutral Current
Allows Fault Detection in Two-Wire Distribution Systems
The AD7751 Uses the Larger of the Two Currents (Phase
or Neutral) to Bill—Even During a Fault Condition
Two Logic Outputs (FAULT and REVP) Can Be Used to
Indicate a Potential Miswiring or Fault Condition
Direct Drive for Electromechanical Counters and
Two-Phase Stepper Motors (F1 and F2)
A PGA in the Current Channel Allows the Use of Small
Values of Shunt and Burden Resistance
Proprietary ADCs and DSP Provide High Accuracy Over
Large Variations in Environmental Conditions and
Time
On-Chip Power Supply Monitoring
On-Chip Creep Protection (No Load Threshold)
On-Chip Reference 2.5 V ؎ 8% (30 ppm/؇C Typical)
with External Overdrive Capability
Single 5 V Supply, Low Power (15 mW Typical)
Low Cost CMOS Process
GENERAL DESCRIPTION
The AD7751 is a high accuracy fault tolerant electrical energy
measurement IC intended for use with two-wire distribution
systems. The part specifications surpass the accuracy require-
ments as quoted in the IEC1036 standard.
The only analog circuitry used on the AD7751 is in the ADCs
and reference circuit. All other signal processing (e.g., multipli-
cation and filtering) is carried out in the digital domain. This
approach provides superior stability and accuracy over extremes
in environmental conditions and over time.
The AD7751 incorporates a novel fault detection scheme that
both warns of fault conditions and allows the AD7751 to con-
tinue accurate billing during a fault event. The AD7751 does
this by continuously monitoring both the phase and neutral
(return) currents. A fault is indicated when these currents
differ by more than 12.5%. Billing is continued using the larger
of the two currents when the difference is greater than 14%.
Energy Metering IC
with On-Chip Fault Detection
AD7751*
FUNCTIONAL BLOCK DIAGRAM
G0 G1 AV_DD AGND
FAULT
AC/DC DV_DD DGND
AD7751
POWER
SUPPLY MONITOR
SIGNAL
PROCESSING
V1A
A< >B
. . .110101. . .
BLOCK
PGA
ADC
A >B
HPF
V1N
؋1, ؋2, ؋8, ؋16
⌽
V1B
PGA
. . .110101. . .
ADC
B>A
PHASE
CORRECTION _MULTIPLIER
؋1, ؋2, ؋8, ؋16
V2P
. . .11011001. . .
ADC
V2N
LPF
2.5V
4k⍀
REFERENCE
DIGITAL-TO-FREQUENCY
CONVERTER
CLKOUT
REF_IN/OUT CLKIN
SCF S0 S1 REVP CF F1 F2 RESET
The AD7751 supplies average real power information on the
low frequency outputs F1 and F2. These logic outputs may be
used to directly drive an electromechanical counter or interface
to an MCU. The CF logic output gives instantaneous real
power information. This output is intended to be used for cali-
bration purposes.
The AD7751 includes a power supply monitoring circuit on the
AV_DD supply pin. The AD7751 will remain in a reset condition
until the supply voltage on AV_DD reaches 4 V. If the supply falls
below 4 V, the AD7751 will also be reset and no pulses will be
issues on F1, F2 and CF.
Internal phase matching circuitry ensures that the voltage and
current channels are matched whether the HPF in Channel 1
is on or off. An internal no-load threshold ensures that the
AD7751 does not exhibit any creep when there is no load.
The AD7751 is available in 24-lead DIP and SSOP packages.
*Protected by U.S. Patent Nos. 5,745,323; 5,760,617; 5,862,069 and
5,872,469.
REV. 0
Information furnished by Analog Devices is believed to be accurate and
reliable. However, no responsibility is assumed by Analog Devices for its
use, nor for any infringements of patents or other rights of third parties
which may result from its use. No license is granted by implication or
otherwise under any patent or patent rights of Analog Devices.
One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106, U.S.A.
Tel: [phone] World Wide Web Site: http://www.analog.com
Fax: [phone]
© Analog Devices, Inc., 1999