AD7492_15 Datasheet, PDF (1/24 Pages) Analog Devices – 1.25 MSPS, 16 mW Internal REF and CLK, 12-Bit Parallel ADC

1.25 MSPS, 16 mW Internal REF and CLK,
12-Bit Parallel ADC
AD7492
FEATURES
Specified for VDD of 2.7 V to 5.25 V
Throughput rate of 1 MSPS (AD7492)
Throughput rate of 1.25 MSPS (AD7492-5)
Throughput rate of 400 kSPS (AD7492-4)
Low power
4 mW typ at 1 MSPS with 3 V supplies
11 mW typ at 1 MSPS with 5 V supplies
Wide input bandwidth
70 dB typ SNR at 100 kHz input frequency
2.5 V internal reference
On-chip CLK oscillator
Flexible power/throughput rate management
No pipeline delays
High speed parallel interface
Sleep mode: 50 nA typ
24-lead SOIC and TSSOP packages
GENERAL DESCRIPTION
The AD7492, AD7492-4, and AD7492-5 are 12-bit high speed,
low power, successive approximation ADCs. The parts operate
from a single 2.7 V to 5.25 V power supply and feature
throughput rates up to 1.25 MSPS. They contain a low noise,
wide bandwidth track/hold amplifier that can handle
bandwidths up to 10 MHz.
The conversion process and data acquisition are controlled
using standard control inputs allowing for easy interface to
microprocessors or DSPs. The input signal is sampled on the
falling edge of CONVST and conversion is also initiated at this
point. The BUSY pin goes high at the start of conversion and
goes low 880 ns (AD7492/AD7492-4) or 680 ns (AD7492-5)
later to indicate that the conversion is complete. There are no
pipeline delays associated with the part. The conversion result is
accessed via standard CS and RD signals over a high speed
parallel interface.
The AD7492 uses advanced design techniques to achieve very
low power dissipation at high throughput rates. With 5 V
supplies and 1.25 MSPS, the average current consumption
AD7492-5 is typically 2.75 mA. The part also offers flexible
power/throughput rate management.
It is also possible to operate the part in a full sleep mode and a
partial sleep mode, where the part wakes up to do a conversion
and automatically enters a sleep mode at the end of conversion.
Rev. A
Information furnished by Analog Devices is believed to be accurate and reliable. However, no
responsibility is assumed by Analog Devices for its use, nor for any infringements of patents or other
rights of third parties that may result from its use. Specifications subject to change without notice. No
license is granted by implication or otherwise under any patent or patent rights of Analog Devices.
Trademarks and registered trademarks are the property of their respective owners.
FUNCTIONAL BLOCK DIAGRAM
AV_DD
4
2.5V
REF
DV_DD
20
BUF
REF OUT
5
V_DRIVE
21
CLOCK
OSCILLATOR
V_IN ⁶
T/H
12-BIT SAR
ADC
OUTPUT
DRIVERS
DB11
DB0
CONVST 10
AD7492
CONTROL
LOGIC
7
AGND
Figure 1.
19
DGND
11 PS/FS
8 CS
9 _RD
12 BUSY
The type of sleep mode is hardware selected by the PS/FS pin.
Using these sleep modes allows very low power dissipation
numbers at lower throughput rates.
The analog input range for the part is 0 V to REFIN. The
2.5 V reference is supplied internally and is available for
external referencing. The conversion rate is determined by the
internal clock.
PRODUCT HIGHLIGHTS
1. High Throughput with Low Power Consumption. The
AD7492-5 offers 1.25 MSPS throughput with 16 mW
power consumption.
2. Flexible Power/Throughput Rate Management. The
conversion time is determined by an internal clock. The
part also features two sleep modes, partial and full, to
maximize power efficiency at lower throughput rates.
3. No Pipeline Delay. The part features a standard successive
approximation ADC with accurate control of the sampling
instant via a CONVST input and once-off conversion
control.
4. Flexible Digital Interface. The VDRIVE feature controls the
voltage levels on the I/O digital pins.
5. Fewer Peripheral Components. The AD7492 optimizes
PCB space by using an internal reference and internal CLK.
One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106, U.S.A.
Tel: [phone]
www.analog.com
Fax: [phone]
©2006 Analog Devices, Inc. All rights reserved.