AD7352 Datasheet, PDF (1/20 Pages) Analog Devices – Differential Input, Dual, Simultaneous Sampling, 3 MSPS, 12-Bit, SAR ADC

Differential Input, Dual, Simultaneous
Sampling, 3 MSPS, 12-Bit, SAR ADC
AD7352
FEATURES
Dual 12-bit SAR ADC
Simultaneous sampling
Throughput rate: 3 MSPS per channel
Specified for VDD at 2.5 V
No conversion latency
Power dissipation: 26 mW at 3 MSPS
On-chip reference: 2.048 V ± 0.25%, 6 ppm/°C
Dual conversion with read
High speed serial interface: SPI-/QSPI™-/MICROWIRE™-/ DSP-
compatible
−40°C to +125°C operation
Available in a 16-lead TSSOP
V_INA+
V_INA–
REF_A
FUNCTIONAL BLOCK DIAGRAM
V_DD
V_DRIVE
AD7352
T/H
12-BIT
SUCCESSIVE
APPROXIMATION
ADC
SDATA_A
BUF
REF
BUF
CONTROL
LOGIC
SCLK
CS
REF_B
V_INB+
V_INB–
12-BIT
SUCCESSIVE
T/H
APPROXIMATION
ADC
SDATA_B
GENERAL DESCRIPTION
The AD7352¹ is a dual, 12-bit, high speed, low power, successive
approximation ADC that operates from a single 2.5 V power
supply and features throughput rates up to 3 MSPS. The part
contains two ADCs, each preceded by a low noise, wide band-
width track-and-hold circuit that can handle input frequencies
in excess of 110 MHz.
The conversion process and data acquisition use standard
control inputs allowing for easy interfacing to microprocessors
or DSPs. The input signal is sampled on the falling edge of CS;
and a conversion is also initiated at this point. The conversion
time is determined by the SCLK frequency.
The AD7352 uses advanced design techniques to achieve very
low power dissipation at high throughput rates. With a 2.5 V
supply and a 3 MSPS throughput rate, the part consumes 10 mA
typically. The part also offers a flexible power/throughput rate
management options.
The analog input range for the part is the differential common-
mode ±VREF/2. The AD7352 has an on-chip 2.048 V reference
that can be overdriven when an external reference is preferred.
The AD7352 is available in a 16-lead thin shrink small outline
package (TSSOP).
AGND
AGND
REFGND
Figure 1.
DGND
PRODUCT HIGHLIGHTS
1. Two Complete ADC Functions.
These functions allow simultaneous sampling and conversion
of two channels. The conversion result of both channels is
simultaneously available on separate data lines or in suc-
cession on one data line if only one serial port is available.
2. High Throughput With Low Power Consumption.
The AD7352 offers a 3 MSPS throughput rate with 26 mW
power consumption.
3. No Conversion Latency.
The AD7352 features two standard successive approx-
imation ADCs with accurate control of the sampling
instant via a CS input and, once off, conversion control.
Table 1. Related Devices
Generic Resolution Throughput
AD7356 12-bit
5 MSPS
AD7266 12-bit
2 MSPS
AD7866 12-bit
1 MSPS
AD7366 12-bit
1 MSPS
AD7367 14-bit
1 MSPS
Analog Input
Differential
Differential/single ended
Single-ended
Single-ended bipolar
Single-ended bipolar
1 _{Protected by U.S. Patent No. 6,681,332.}
Rev. 0
Information furnished by Analog Devices is believed to be accurate and reliable. However, no
responsibility is assumed by Analog Devices for its use, nor for any infringements of patents or other
rights of third parties that may result from its use. Specifications subject to change without notice. No
license is granted by implication or otherwise under any patent or patent rights of Analog Devices.
Trademarks and registered trademarks are the property of their respective owners.
One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106, U.S.A.
Tel: [phone]
www.analog.com
Fax: [phone]
©2008 Analog Devices, Inc. All rights reserved.