English
Language : 

AAT3200 Datasheet, PDF (11/16 Pages) Advanced Analogic Technologies – OmniPower LDO Linear Regulator
AAT3200
OmniPower™ LDO Linear Regulator
At any given ambient temperature (TA), the maxi-
mum package power dissipation can be deter-
mined by the following equation:
PD(MAX)
=
TJ(MAX) -
θJA
TA
Constants for the AAT3200 are TJ(MAX), the maxi-
mum junction temperature for the device (125°C)
and ΘJA = 200°C/W, the SC59 thermal resistance.
Typically, maximum conditions are calculated at the
maximum operating temperature where TA = 85°C,
under normal ambient conditions TA = 25°C. Given
TA = 85°C, the maximum package power dissipa-
tion is 200mW. At TA = 25°C, the maximum pack-
age power dissipation is 500mW.
The maximum continuous output current for the
AAT3200 is a function of the package power dissi-
pation and the input-to-output voltage drop across
the LDO regulator. Refer to the following simple
equation:
IOUT(MAX) <
PD(MAX)
VIN - VOUT
For example, if VIN = 5V, VOUT = 3V, and TA = 25°C,
IOUT(MAX) < 250mA. The output short-circuit protec-
tion threshold is set between 150mA and 300mA.
If the output load current were to exceed 250mA or
if the ambient temperature were to increase, the
internal die temperature will increase. If the condi-
tion remained constant and the short-circuit protec-
tion were not to activate, there would be a potential
damage hazard to LDO regulator since the thermal
protection circuit will only activate after a short-cir-
cuit event occurs on the LDO regulator output.
To determine the maximum input voltage for a
given load current, refer to the following equation.
This calculation accounts for the total power dissi-
pation of the LDO regulator, including that caused
by ground current.
PD(MAX) = (VIN - VOUT)IOUT + (VIN × IGND)
This formula can be solved for VIN to determine the
maximum input voltage.
VIN(MAX)
=
PD(MAX) + (VOUT × IOUT)
IOUT + IGND
The following is an example for an AAT3200 set for
a 3.0V output:
From the discussion above, PD(MAX) was deter-
mined to equal 417mW at TA = 25°C.
VOUT = 3.0V
IOUT = 150mA
IGND = 20µA
500mW + (3.0V × 150mA)
VIN(MAX) =
150mA + 20µA
VIN(MAX) > 5.5V
Thus, the AAT3200 can sustain a constant 3.0V
output at a 150mA load current as long as VIN is ≤
5.5V at an ambient temperature of 25°C. 5.5V is
the maximum input operating voltage for the
AAT3200, thus at 25°C, the device would not have
any thermal concerns or operational VIN(MAX) limits.
This situation can be different at 85°C. The follow-
ing is an example for an AAT3200 set for a 3.0V
output at 85°C:
From the discussion above, PD(MAX) was deter-
mined to equal 200mW at TA = 85°C.
VOUT = 3.0V
IOUT = 150mA
IGND = 20µA
200mW + (3.0V × 150mA)
VIN(MAX) =
150mA + 20µA
VIN(MAX) = 4.33V
3200.2006.02.1.4
11