|
RCM10A-1R0FYB Datasheet, PDF (1/1 Pages) American Accurate Components, Inc. – HIGH POWER RESISTOR - Non Inductive Chassis Mounting | |||
|
HIGH POWER RESISTOR â Non Inductive Chassis Mounting
The content of this specification may change without notification 12/12/07
Custom solutions are available.
HOW TO ORDER
RCM 100 - 102 K N B
Packaging
B = bulk
TCR (ppm/°C)
Y = +50 N= +250
Tolerance
F = +1% J = +5% K= +10%
Resistance (â¦)
1R0 = 1.0
100 = 10
Rated Power
10A = 10 W
10B = 10 W
50 = 50 W
101 = 100
102 = 1.0K
100 = 100 W
250 = 250 W
Series
High Power Resistor, Non-Inductive, Chassis Mounting
SCHEMATIC & DIMENSIONS (mm)
FEATURES
 Chassis mounting high power resistor 10W to 250W rated power
 Small in regard to thickness and with vertical terminal wires
 Suitable for high density electronic design.
 Decrease in the inductive effect in power electronics circuits
 Complete thermal conduction and heat dissipation design
APPLICATIONS
 Gate resistors and snubber resistors in power supply
 Load resistors and dumping resistors in high end audio
 Precision terminal resistor in RF amplifiers
Note: Lead material is solder plated Copper
RCM10A
RCM10B
RCM50
DERATING CURVE
RCM10, RCM50
% Rated Power
RCM100
RCM100, RCM250
% Rated Power
RCM250
Custom solutions are available
For more information; send your specification to sales@aacix.com.
Flange Temperature °C
SPECIFICATIONS & PERFORMANCE
Model
Rated Power
Resistance Range (â¦) E24
TCR (ppm/°C)
Resistance Tolerance
Operating Temperature Range
Temperature Cycle
Withstanding Voltage
Maximum Applied Voltage
Load Life
Humidity
Short Time Overload
Soldering Heat
Solderability
Insulation Resistance
Vibration
RCM10
RCM-50
RCM100
RCM250
10 W
50 W
100 W
250 W
10.0 ~ 20K
10.0 ~ 1.0K
10.0 ~ 1.0K
1.0 ~ 1.0K
±50
±50
±250
±250
±1%, ±5%
±1%, ±5%
±10%
±10%
-55°C ~ +155°C
-55°C ~ +120°C
± (0.25% + 0.05 â¦)
± (1.0% + 0.05 â¦)
1,000V DC
2,000V DC
5,000V DC
5,000V DC
E = âP*R
± (1.0% + 0.05 â¦)
± (1.0% + 0.05 â¦)
± (0.25% + 0.05 â¦)
± (0.25% + 0.05 â¦)
> 75% of round
> 1000 Meg ohm
± (0.25% + 0.05 â¦)
Flange Temperature °C
Test Condition
With heat sink , 2.8°C/W
2.0 ⦠and 5.0 ⦠are also available
-55°C ~ +155°C
-55°C, 30 min., +155°C (or+120°C for RCM100 & RCM250), 30 min.; 20 cycles
60 seconds
25°C, 90 min. on, 30 min. off, 1000 hrs
70°C, 90 ~ 95% RH, DC 0.1W, 1000 hrs
Rated power x 2.5, 2.5 sec. with heat sink
350°C ± 5°C, 3 sec.
230°C ± 5°C, 3 sec.
Between terminals and tab
American Accurate Components, Inc.
188 Technology Drive, Unit H, Irvine, CA 92618
1
TEL: 949-453-9888 Â FAX: 949-453-8889
|