N3429-630T02RB Datasheet, PDF (3/5 Pages) 3M Electronics – 3M™ Four-Wall Header .100” × .100” Latch/Ejector, Straight, Compliant Pin

3M^™ Four-Wall Header
.100” × .100” Latch/Ejector, Straight, Compliant Pin
3000 Series
Pin Qty
3M Part
Number
A
10
3793 1.26 (32.1)
14
3314 1.46 (37.2)
16
3408 1.56 (39.7)
20
3428 1.76 (44.8)
24
3627 1.96 (49.9)
26
3429 2.06 (52.4)
30
3440 2.26 (57.5)
34
3431 2.46 (62.6)
40
3432 2.76 (70.2)
50
3433 3.26 (82.9)
60
3372 3.76 (95.6)
64
3764 3.96 (100.7)
Dimensions
B
C
1.105 (28.07)
1.305 (33.15)
1.405 (35.69)
1.605 (40.77)
1.805 (45.85)
1.905 (48.39)
2.105 (53.47)
2.305 (58.55)
2.605 (66.17)
3.105 (78.87)
3.605 (91.57)
3.805 (96.65)
0.865 (21.97)
1.065 (27.05)
1.165 (29.59)
1.365 (34.67)
1.565 (39.75)
1.665 (42.29)
1.865 (47.37)
2.065 (52.45)
2.365 (60.07)
2.865 (72.77)
3.365 (85.47)
3.565 (90.55)
D
0.71 (18.0)
0.91 (23.1)
1.01 (25.6)
1.21 (30.7)
1.41 (35.8)
1.51 (38.3)
1.71 (43.4)
1.91 (48.5)
2.21 (56.1)
2.71 (68.8)
3.21 (81.5)
3.41 (86.6)
Polarizing
Notches
Provided
BC
BC
ABC
ABC
ABC
ABC
ABC
ABC
ABC
ABC
ABC
ABC
Insertion platen
3442-00XX
3442-0048
3442-0049
3442-0050
3442-0051
3442-0052
3442-0053
3442-0054
3442-0055
3442-0056
3442-0057
3442-0058
3442-0059
.300 Min
[7.62]
Side to Side
Stackability
.106
[2.69] or
(See Note 2)
.116
[2.95]
See Note 3
R
S
T
R
Tail
Section
S
Compliant Section
T
Mating
4X R .009 Max
[0.23]
Area
.060
[1.52]
.100 ± .003
[2.54]
Position 1
.100 ± .003
[2.54]
.352
[8.94]
B
4X .002 ± .001
[0.05]
Break Edges
Section T-T
Section R-R
R .020 Sym
[0.51]
Recommended Mounting Hole Pattern
Note:
3. Listed below are the PCB hole sizes and tolerances recommended for use with 3M’s compliant
pin header. The insertion force is designed not to exceed 40 pounds per pin and the withdrawal
force is not less than 10 pounds per pin.
4. Use of snap-in latch/ejectors in either short (N3XXX-650T02XX) or long (N3XXX-660T02XX)
styles, installed or shipped separately. (-5 & -6 snap-in latches are dimensionally and functionally
equivalent to -2 & -3 roll pin latches)
If ordering Snap-In style latches separately, please use the chart below
Short Latch
Long Latch
Color
High Temp (PPA)
3505-30
3505-31
Gray
High Temp (PPA)
N3505-30B
N3505-31B
Black
Section S-S
Pin Cross Sections
Hole Size for:
Preferred Drilled - ø.0453 ± .0005
Acceptable Drilled - ø.0453 +.0005
-.0010
After Etchback - ø.0460 Max
After Plating - .ø040 ± .003
Board thickness - .093 to .150
Plating:
.001 Minimum Copper plating thickness
.0003 Min Tin plating
Ordering Information
X XXXX - 6X0T02XX
Prefix:
Blank = Std.Temp Gray (PBT): (TC Plating Req’d)
N = High Temp Black (PCT) (RB Plating Req’d)
3M Part Number
Assembly Equipment: Use 3442-00XX platen (see chart above) and
appropriate commercial arbor press to press header into pc board.
Plating suffix:
TC = 30 μ” Gold w/Tin-Lead Tails (App. E2 & C2 Apply)
RB = 30 μ” Gold w/Matte Tin Tails (App. E1 & C1 Apply)
Latch/Ejector System:
0 = No latch/ejectors
2 = Short latch/ejectors
3 = Long latch/ejectors
5 = Short, Snap-In Latch/Ejectors
6 = Long, Snap-In Latch/Ejectors
TS-0478-D
Sheet 3 of 4
3
Electronic Solutions Division
Interconnect Solutions
http://www.3Mconnectors.com
3M is a trademark of 3M Company.
For technical, sales or ordering information call
800-225-5373