N3408-6002RB Datasheet, PDF (3/5 Pages) 3M Electronics – .100 × .100 Latch/Ejector, Straight and Right Angle

3M^™ Four-Wall Header
.100" × .100" Latch/Ejector, Straight and Right Angle
3000 Series
Pin Qty
06
08
10
14
16
20
24
26
30
34
40
50
60
64
3M Part
Number
3869
3889
3793
3314
3408
3428
3627
3429
3440
3431
3432
3433
3372
3764
A
1.065 (27.05)
1.165 (29.59)
1.265 (32.13)
1.465 (37.21)
1.565 (39.75)
1.765 (44.83)
1.965 (49.91)
2.065 (52.45)
2.265 (57.53)
2.465 (62.61)
2.765 (70.23)
3.265 (82.93)
3.765 (95.63)
3.965 (100.71)
Table 1
Dimensions
B
C
0.905 (22.99)
0.665 (16.89)
1.005 (25.53)
0.765 (19.43)
1.105 (28.04)
0.865 (21.97)
1.305 (33.12)
1.065 (27.05)
1.405 (35.66)
1.165 (29.59)
1.605 (40.74)
1.365 (34.67)
1.805 (45.82)
1.565 (39.75)
1.905 (48.36)
1.665 (42.29)
2.105 (53.44)
1.865 (47.37)
2.305 (58.52)
2.065 (52.45)
2.605 (66.14)
2.365 (60.07)
3.105 (78.84)
2.865 (72.77)
3.605 (91.54)
3.365 (85.47)
3.805 (96.62)
3.565 (90.55)
* Available without center notch B. Contact 3M.
D
0.505 (12.83)
0.605 (15.37)
0.705 (17.91)
0.905 (22.99)
1.005 (25.53)
1.205 (30.61)
1.405 (35.69)
1.505 (38.23)
1.705 (43.31)
1.905 (48.39)
2.205 (56.01)
2.705 (68.71)
3.205 (81.41)
3.405 (86.49)
Polarizing
Notches
B*
B*
BC
BC
ABC
ABC
ABC
ABC
ABC
ABC
ABC
ABC
ABC
ABC
Inch
(mm)
Tolerance Unless Noted
.0 .00 .000
Inch ± .1 ^{± .01 ± .005}
[ ] Dimensions for
Reference only
3M Part
Number Suffix
-5XX2
-6XX2
-5X03
-6X03
Table 2
Contact Tail
Dim E
Pin Cross Section
Solder Tail for
.062 (1.57)
Thick PC Board
Solder Tail for 0.94
(2.39) to .125 (3.18)
Thick PC Board
.112 ± .010
(2.84)
.155 ± .010
(3.94)
Dim F
.0245 ± .0005
(0.622)
.0245 ± .0005
(0.622)
Diagonals
.028 ± .001
(0.71)
.028 ± .001
(0.71)
Corner Radii
.0075 Ref
(0.191)
.0075 Ref
(0.191)
ø.106 ^or ø.116
[2.69]
[2.95]
.300
(See Note 2)
[7.62]
Side to Side Stackability _{Dim G}
Dim G
0.035 ± .003
(0.89) (See Note 3)
0.035 ± .003 (0.89)
ø.106 or ø.116
[2.69]
[2.95]
.41
[10.4]
(See Note 2)
Max to Edge of PCB
for Daisy Chain
Dim G
“Y” ^CL
"Y" CL
.060
[1.52]
Position 1
.100 ± .003
[2.54]
.100 ± .003
[2.54]
.352
[8.94]
B
Recommended Mounting Hole Pattern
(Straight)
.029
[0.74]
.100 ± .003
[2.54]
Position 1
.100 ± .003
[2.54]
.232
[5.89]
C
Recommended Mounting Hole Pattern
(Right Angle)
Notes: 1. Notches A & C will accomodate 3M Polarizing Keys (3M Part #3518 or #N3518).
2. Mounting hardware: From solder side of pc board use #4-24 thread cutting screw (3M Part # 3341-5) and .116 [2.95] dia mounting hole. For right angle version only, #2-56 bolt and nut (3M
Part # 3341-6) with .106 [2.69] dia mounting hole may be used. See illustrations on page 4.
3. The recommended PCB hole size for the kinked tail positions on the .112 solder tail connector is .035 ± .002. See page 4 for kink position details (K2 version).
4. Contact your 3M sales representative for custom requirements.
Ordering Information
N = High Temp Black (PCT)/(RB Plating Req’d)
Blank = Std. Temp Gray (PBT) /(Blank or UB Pltg. Req’d.)
X3XXX-XXXXXX
3M Part Number
(See Table 1)
Pin Configuration
5 = Right Angle Solder Tails
6 = Straight Solder Tails
Latch/Ejector System
0 = No Latch/Ejector installed
2 = Short Roll Pin Latch/Ejectors
3 = Long, Roll Pin Latch/Ejectors
5 = Short, Snap-In Latch/Ejectors
6 = Long, Snap-In Latch/Ejectors
Plating
RB = 30 μ” [ 0.76 μm ] Gold and 200 μ” [ 5.08 μm ] Matte Tin
(App. E1 & C1 Apply)
Blank or UB = 30 μ” (0.76 μm ] Gold and 200 μ” [ 5.08 μm ]
Tin Lead (App. E3 & C2 Apply)
Tail
02 = for .062 [1.57] thick board
03 = for .094 to .125 [2.39 to 3.18] thick board
K2 = kinked for .062 [1.57] thick board
TS-0772-P
Sheet 3 of 4
3
Electronic Solutions Division
Interconnect Solutions
http://www.3Mconnectors.com
3M is a trademark of 3M Company.
For technical, sales or ordering information call
800-225-5373