D3793-6202-AR Datasheet, PDF (3/5 Pages) 3M Electronics – 100” × .100” Latch/Ejector, Straight and Right Angle

3M^™ Four-Wall Header
.100” × .100” Latch/Ejector, Straight and Right Angle
D3000 Series
Table 1
Pin Qty
3M Part
Number
A
Dimensions
B
C
06
3869
1.065 (27.05)
0.905 (22.99)
0.665 (16.89)
08
3889
1.165 (29.59)
1.005 (25.53)
0.765 (19.43)
10
3793
1.265 (32.13)
1.105 (28.04)
0.865 (21.97)
14
3314
1.465 (37.21)
1.305 (33.12)
1.065 (27.05)
16
3408
1.565 (39.75)
1.405 (35.66)
1.165 (29.59)
20
3428
1.765 (44.83)
1.605 (40.74)
1.365 (34.67)
24
3627
1.965 (49.91)
1.805 (45.82)
1.565 (39.75)
26
3429
2.065 (52.45)
1.905 (48.36)
1.665 (42.29)
30
3440
2.265 (57.53)
2.105 (53.44)
1.865 (47.37)
34
3431
2.465 (62.61)
2.305 (58.52)
2.065 (52.45)
40
3432
2.765 (70.23)
2.605 (66.14)
2.365 (60.07)
50
3433
3.265 (82.93)
3.105 (78.84)
2.865 (72.77)
60
3372
3.765 (95.63)
3.605 (91.54)
3.365 (85.47)
64
3764
3.965 (100.71)
3.805 (96.62)
3.565 (90.55)
* Available without center notch B. Contact 3M.
D
0.505 (12.83)
0.605 (15.37)
0.705 (17.91)
0.905 (22.99)
1.005 (25.53)
1.205 (30.61)
1.405 (35.69)
1.505 (38.23)
1.705 (43.31)
1.905 (48.39)
2.205 (56.01)
2.705 (68.71)
3.205 (81.41)
3.405 (86.49)
Polarizing
Notches
B*
B*
BC
BC
ABC
ABC
ABC
ABC
ABC
ABC
ABC
ABC
ABC
ABC
Inch
(mm)
Tolerance Unless Noted
.0 .00 .000
± .1 ± .01 ± .005
[ ] Dimensions for
Reference only
3M Part
Number Suffix
-5XX2
-6XX2
Contact Tail
Solder Tail for
.062 [1.57]
Thick PC Board
Dim E
.112 ± .010
[2.84]
Table 2
Dim F
Pin Cross Section
Diagonals Corner Radii
.0245 ± .0005
[0.622]
.028 ± ..001
[0.71]
.0075 Ref
[0.191]
Dimension G
Ø.035 ±.003
[0.89] (See Note 3)
ø.106 _{or ø.116}
[2.69]
[2.95]
(See Note 2)
.300
[7.62]
Side to Side Stackability _{Dim G}
ø.106 or ø.116
[2.69]
[2.95]
.41
[10.4]
(See Note 2)
Max to Edge of PCB
for Daisy Chain
Dim G
“Y” ^CL
"Y" CL
.060
[1.52]
Position 1
.100 ± .003
[2.54]
.100 ± .003
[2.54]
.352
[8.94]
B
Recommended Mounting Hole Pattern
(Straight)
.029
[0.74]
.100 ± .003
[2.54]
Position 1
.100 ± .003
[2.54]
.232
[5.89]
C
Recommended Mounting Hole Pattern
(Right Angle)
Notes:
1. Notches A & C will accomodate 3M Polarizing Keys (3M Part #3518 or #N3518).
2. Mounting hardware: From solder side of pc board use #4-24 thread cutting screw (3M Part # 3341-5) and .116 [2.95] dia mounting hole.
For right angle version only, #2-56 bolt and nut (3M Part # 3341-6) with .106 [2.69] dia mounting hole may be used. See illustrations on page 4.
3. Contact your 3M sales representative for custom requirements.
Ordering Information
D3XXX - XX02AR
Pin Configuration
5 = Right Angle Solder Tails
6 = Straight Solder Tails
3M Part Number
(See Table 1)
Latch/Ejector System
0 = No Latch/Ejector installed
2 = Short Roll Pin Latch/Ejectors
3 = Long Roll Pin Latch/Ejectors
3
Electronic Solutions Division
Interconnect Solutions
http://www.3Mconnectors.com
Tail
02 = for .062 [1.57] thick board
TS-2245-F
Sheet 3 of 4
3M is a trademark of 3M Company.
For technical, sales or ordering information call
800-225-5373