3431-D002 Datasheet, PDF (3/5 Pages) 3M Electronics – 3M™ Three-Wall Condo Header .100 × .100 Right Angle

3M^™ Three-Wall Condo Header
.100 × .100 Right Angle
Pin
3M Part
Quantity Number
20
3793
28
3314
32
3408
40
3428
48
3627
52
3429
60
3440
68
3431
80
3432
100
3433
120
3372
128
3764
A
1.26 (32.1)
1.46 (37.2)
1.56 (39.7)
1.76 (44.8)
1.96 (49.8)
2.06 (52.4)
2.26 (57.4)
2.46 (62.6)
2.76 (70.2)
3.26 (82.9)
3.76 (95.6)
3.96 (100.7)
Table 1
Dimensions
C
0.865 (21.97)
1.065 (27.05)
1.165 (29.59)
1.365 (34.67)
1.565 (39.75)
1.665 (42.29)
1.865 (47.37)
2.065 (52.45)
2.365 (60.07)
2.865 (72.77)
3.365 (85.47)
3.565 (90.55)
.029 Typ
[0.74]
D
0.71 (18.0)
0.91 (23.1)
1.01 (25.6)
1.21 (30.7)
1.41 (35.8)
1.51 (38.3)
1.71 (43.4)
1.91 (48.5)
2.21 (56.1)
2.71 (68.8)
3.21 (81.5)
3.41 (86.6)
Polarizing
Notches
BC
BC
ABC
ABC
ABC
ABC
ABC
ABC
ABC
ABC
ABC
ABC
.232
[5.89]
3000 Series
ø .100 Typ
[2.54]
.100 Typ
[2.54]
Position 1
.100 Typ
[2.54]
ø.040 ± .003
[ 1.02 ]
(After Plating)
Recommended Hole Pattern
Notes:
1. Notches A & C will accomodate 3M Polarizing Key (3M Part Number 3518 or N3518).
2. 112 [2.84] tail length suitable for .062 [1.57] thick pc board.
3. Contact your 3M sales representative for custom requirements.
4. Use of snap-in style latch/ejectors in either short (X3XXX-D502XX) or X3XXX-D602XX) styles, installed or shipped
separately (-5 & -6 snap-in latches are dimensionally and functionally equivalent to -2 & -3 roll pin latches)
5. Mounting hardware: From solder side of pc board use #4-*24 thread cutting screw (3M Part 3341-5) and .116 dia. mounting hole. See Illustrations on
page 4.
If ordering Snap-In style latches separately, please use the below chart
High Temp (PBT)
High Temp (PPA)
Short Latch
3505-30
N3505-30B
Long Latch
3505-31
N3505-31B
Color
Gray
Black
Inch
(mm)
Tolerance Unless Noted
.0 .00 .000
Inch ± .1 ± .01 ± .005
[ ] Dimensions for
Reference only
Ordering Information
X3XXX - DX02XX
N = High Temp Black (PCT) (RB Plating Req’d)
Blank = Std. Temp Gray (PBT) (Blank or UB Pltg. Req’d.)
3M Part Number
RB = 30μ” [0.76μm] Gold with Matte Tin Tails (App. E1 & C1 Apply)
Blank or UB = 30μ” [0.76μm] Gold with Tin Lead Tails (App. E3 & C2
Apply)
Latch/Ejector System
0 = No Latch/Ejector Installed
2 = Short, Roll Pin Latch/Ejectors
3 = Long, Roll Pin Latch/Ejectors
TS-0773-G
Sheet 3 of 4
3
Electronic Solutions Division
Interconnect Solutions
http://www.3Mconnectors.com
3M is a trademark of 3M Company.
For technical, sales or ordering information call
800-225-5373