10214-1210VE Datasheet, PDF (3/4 Pages) 3M Electronics – 3M Mini D Ribbon (MDR) Connectors

3M™ Mini D Ribbon (MDR) Connectors
.050″ Surface Mount Right Angle Receptacle - Shielded
102 Series
Contact
Quantity
A ± .002
Dimensions
B ± .002
C ± .002
Recommended Board Layout
(viewed from connector side)
14 .930 [ 23.64 ] .500 [ 12.70 ] .325 [ 8.26 ]
20 1.081 [ 27.45 ] .650 [ 16.51 ] .475 [ 12.07 ]
26 1.230 [ 31.26 ] .800 [ 20.32 ] .625 [ 15.88 ]
center spacing
C
Solder Pads for Solder
Tail (See below for
more detail)
40 1.581 [ 40.15 ] 1.150 [ 29.21 ] .975 [ 24.77 ]
50 1.831 [ 46.50 ] 1.400 [ 35.56 ] 1.225 [ 31.12 ]
center spacing
.025 ± .0008
.118 [ 3.0 ]
.122 [ 3.1 ]
.165 [ 4.2 ]
.016 ± .0004
.093 ± .0004 _{∅.110 ± .004 (2X)}
Screw Lock
(see notes below)
.138 [ 3.5 ]
.256 [ 6.5 ]
PCB Ref. Edge
Solder Tail Layout Detail
.088 [ 2.223 ]
B
A
.187 max.
[ 4.75 ]
Lockstand Solder
Pad Outline
∅.079 + .004 (2X)
- .000
Positioning Hole
(#'s Correspond to Connector Contact # Shown on Previous Page)
14 Pos. ^{7 6 5 4 3 2 1}
Last 14 13 12 11 10 9 8
Pos. _{PCB Ref. Edge}
Connector Position
(Top Row)
Position
(Bottom Row)
20 Pos. ^{10 9 8 7 6 5 4 3 2 1}
Last
Pos.
20 19 18 17 16 15 14 13 12 11
PCB Ref. Edge
Connector Position
(Top Row)
Position
(Bottom Row)
13 12 11 10 9 8 7 6 5 4 3 2 1
26 Pos.
Last
Pos.
26 25 24 23 22 21 20 19 18 17 16 15 14
PCB Ref. Edge
Connector Position
(Top Row)
Position
(Bottom Row)
40 Pos. _{20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1}
Last
Pos.
40 39 38 37 36 35 34 33 32 31 30 29 28 27 26 25 24 23 22 21
PCB Ref. Edge
Connector
Position
Position
(Bottom Row)
50 Pos. 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1
Last
Pos.
50 49 48 47 46 45 44 43 42 41 40 39 38 37 36 35 34 33 32 31 30 29 28 27 26
PCB Ref. Edge
Connector
Position
Position
(Bottom Row)
Contact
Quantity
14
D
1.10 [ 19.9 ]
E
.931 [ 23.64 ]
Recommended Panel Cut-out
Note: Panel thickness .079 [ 2.00 ] Max.
20
.94 [ 23.8 ] 1.081 [ 27.45 ]
26
1.09 [ 27.6 ] 1.231 [ 31.26 ]
40
1.44 [ 36.5 ] 1.581 [ 40.15 ]
.319 ± .004
[ 8.1 ]
50
1.69 [ 42.8 ] 1.830 [ 46.50 ]
**Notes:
1. Plated through holes for .062″ board thickness.
2. Use mounting screws ( M2.5 ) to fasten to board.
R .060
[ 1.50 ]
D ± .004
E ± .004
TS-0755-10
Sheet 3 of 3
3M
Interconnect Solutions
http://www.3M.com/interconnects/
3M is a trademark of 3M Company.
For technical, sales or ordering information call
800-225-5373